Listar Artículos de revista DCIE - ZIES Aldizkari artikuluak por autor UPNA "Pérez de Landazábal Berganzo, José Ignacio"
Mostrando ítems 1-20 de 21
-
Analysis of the strain misfit between matrix and inclusions in a magnetically tunable composite
A magnetically tunable composite has been elaborated by embedding microparticles of a metamagnetic shape memory alloy on a photo curable resin. The strain misfit between the polymeric matrix and the inclusions has been ... -
Complex selective manipulations of thermomagnetic programmable matter
Programmable matter can change its shape, stiffness or other physical properties upon command. Previous work has shown contactless optically controlled matter or magnetic actuation, but the former is limited in strength ... -
Correlation between particle size and magnetic properties in soft-milled Ni45Co5Mn34In16 powders
The effect of microstructural defects induced by mechanical milling has been studied in a Ni–Mn–In–Co metamagnetic shape memory alloy. The martensitic transformation and Curie temperatures do not change with grinding, thus ... -
Effect of Cu substitution on the magnetic and magnetic induction heating response of CdFe₂O₄ spinel ferrite
In this work, a comparative study of the effect of Cu on the structural, magnetic and magnetic induction heating response in CdFe2O4 spinel is presented. The ceramic nanoparticles (Cu1−xCdxFe2O4; 0 ≤ x ≤ 1) were synthesized ... -
Effect of high-energy ball-milling on the magnetostructural properties of a Ni45Co5Mn35Sn15 alloy
The effect of high-energy ball-milling on the magnetostructural properties of a Ni45Co5Mn35Sn15 alloy in austenitic phase at room temperature has been analyzed by neutron and high-resolution X-ray diffraction. The ball ... -
Experimental observation of vacancy-assisted martensitic transformation shift in Ni-Fe-Ga alloys
Positron annihilation lifetime spectroscopy is used to experimentally demonstrate the direct relationship between vacancies and the shift of the martensitic transformation temperature in a Ni55Fel7Ga28 alloy. The evolution ... -
Fe-C nanoparticles obtained from thermal decomposition employing sugars as reducing agents
The aim of the work is to present a comparative analysis (structural and magnetic) of Fe-C nanocomposites obtained by the thermal decomposition of sugars (fructose, glucose and sucrose) employing FeCl3 as Fe3+ precursor. ... -
Giant stress impedance magnetoelastic sensors employing soft magnetic amorphous ribbons
Soft magnetic amorphous alloys obtained via rapid quenching techniques are widely employed in different technological fields such as magnetic field detection, bio labeling, non-contact positioning, etc. Among them, ... -
Identification of a Ni-vacancy defect in Ni-Mn-Z (Z = Ga, Sn, In): an experimental and DFT positron-annihilation study
By means of experimental positron-annihilation-lifetime measurements and theoretical density functional theory (DFT) positron-lifetime calculations, vacancy-type defects in Ni50Mn50−xSnx (x = 25, 20, 15, 13, 10) and ... -
Influence of structural defects on the properties of metamagnetic shape memory alloys
The production of µ-particles of Metamagnetic Shape Memory Alloys by crushing and subsequent ball milling process has been analyzed. The high energy involved in the milling process induces large internal stresses and high ... -
Magnetic behavior in commercial iron-silicon alloys controlled by the dislocation dynamics at temperatures below 420 K
A decrease of the temperature dependent coercive forces up to around 370 K is discovered in iron silicon alloys, both in quenched samples and in samples which were previously thermally treated to achieve the highest magnetic ... -
Magnetic binary encoding system based on 3D printing and GMI detection prototype
In this work, the feasibility of a magnetic binary encoding system using 3D printing technology is analyzed. The study has a double interest, that is, the possibility of printing a 3D piece that contains the codified ... -
Magnetically activated 3D printable polylactic acid/polycaprolactone/magnetite composites for magnetic induction heating generation
Additive manufacturing technology has attracted the attention of industrial and technological sectors due to the versatility of the design and the easy manufacture of structural and functional elements based on composite ... -
Magnetically tunable damping in composites for 4D printing
Composite materials are being used in the design of new devices to produce more functional, cheap and on-demand products. In particular, 3D printing technology based on composites opens a huge field enabling the freedom ... -
Martensitic transformation controlled by electromagnetic field: from experimental evidence to wireless actuator applications
Mechanical actuators based on shape memory alloys (SMA) are becoming a key component in the development of novel soft robotic applications and surgically implantable devices. Their working principle relies in the temperature ... -
Monitoring structural transformations in metamagnetic shape memory alloys by non-contact GMI technology
(IOP Publishing, 2023) Artículo / ArtikuluaDifferent applications based on metamagnetic shape memory alloy (MSMA) require monitoring the evolution of the martensitic transformation (MT) to optimize the actuation mechanism. To avoid interaction with the active ... -
Non-linear GMI decoding in 3D printed magnetic encoded systems
The nonlinear giant magnetoimpedance (GMI) effect was explored as a highly sensitive sensing technology in 3D-printed magnetic encoded systems. Magnetic nanoparticles with low (magnetite, Fe3O4) and high (Co ferrite, ... -
Outstanding role of the magnetic entropy in arrested austenite in an ordered Ni45Mn36.7In13.3Co5 metamagnetic shape memory alloy
The relevance of the entropy and in particular the outstanding role of the magnetic contribution is analyzed in a non-equilibrium arrested austenite phase in a Ni 45 Mn 36.7 In 13.3 Co 5 metamagnetic shape memory alloy. ... -
Room temperature huge magnetocaloric properties in low hysteresis ordered Cu-doped Ni-Mn-In-Co alloys
(Elsevier, 2022) Artículo / ArtikuluaThe reduction of the thermal hysteresis in first order magnetostructural transition is a determining factor to decrease energy losses and to improve the efficiency of magnetocaloric cooling based systems. In this work, a ... -
Routes for enhanced magnetism in Ni-Mn-In metamagnetic shape memory alloys
The authors provide in-depth physical insight into the enhancement of the magnetic properties of metamagnetic shape memory alloys produced by thermal treatment and cobalt doping. They use neutron scattering to study the ...