Open Access
Low cutoff wavelength etched SMS structures towards verification of the quality of automotive antifreeze
(IEEE, 2020) Rodríguez Rodríguez, Wenceslao Eduardo; Rodríguez Rodríguez, Adolfo Josué; Ruiz Zamarreño, Carlos; Del Villar, Ignacio; Zúñiga Alanís, Manuel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Gobierno de Navarra / Nafarroako Gobernua, 2019 904 116; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, PJUPNA26
Optical fiber single mode-multimode-single mode (SMS) structures can be used as wavelength detection-based sensors. In this work, we focus on the performance at short wavelengths, where optical sources and detectors are less expensive. Here, a self-image band with a high transmission power is monitored in this short-wavelength range. In addition, the diameter and the length of the SMS structure have been optimized in order to improve the sensitivity of the device. In this sense, a maximum refractive index sensitivity of 305 nm/RIU was achieved by an etched SMS with a diameter of 34μ m. Furthermore, the obtained devices were used for testing the quality of automotive coolant and antifreeze liquid.
Open Access
Monitoring of water freeze-thaw cycle by means of an etched single-mode - multimode - single-mode fiber-optic refractometer
(IEEE, 2023) Socorro Leránoz, Abián Bentor; Aginaga Etxamendi, Concepción Isabel; Díaz Lucas, Silvia; Urrutia Azcona, Aitor; Del Villar, Ignacio; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
As an alternative to the different technologies that permit the detection of in-situ ice formation on different surfaces, this contribution proposes the design of an etched single-mode – multimode – single-mode (E-SMS) fiber-optic-based structure as a multimode interference refractometer. This sensor provides enhanced properties with respect to a basic SMS structure, including a higher sensitivity and periodical interferometry bands that can measure surrounding refractive indices with repeatability and robustness. Since ice and water refractive indices are sufficiently different, this structure has been used to detect the freezing - thawing process of water taking place inside a freezer between -20°C and +20°C. Also, this work intends to show a proof of concept of a simple technology that can be applied in different situations, such as in smart cities, avionics, structural health monitoring or even to avoid a cold chain breakage. Inside, novel developments to better understand the working operation of the E-SMS structure are shown, together with a study on how to correlate optical and thermal measurements from a refractive index point of view.
Open Access
Bloch surface wave resonances generated with dielectric stack of high refractive index contrast deposited on a D-shaped optical fiber for sensing applications
(Optica Publishing Group, 2022) Del Villar, Ignacio; Kwietniewski, Norbert; González-Valencia, Esteban; Burnat, Dariusz; Armas, Dayron; Pitula, Emil; Matías Maestro, Ignacio; Chiavaioli, Francesco; Torres, Pedro; Smietana, Mateusz; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A 5-layer stack composed of TiO2 and Al2O3, two materials with a high refractive index contrast, was deposited on a D-shaped fiber to generate Bloch surface wave resonances with an improved figure of merit.
Open Access
Generation of lossy mode resonances in a broadband range with multilayer coated coverslips optimized for humidity sensing
(Elsevier, 2020) Bohórquez Navarro, Dina Luz; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Coverslips deposited with a metallic oxide can be employed for generating lossy mode resonances by lateral incidence of light on the coverslip. Here it is demonstrated that with copper oxide the fading observed with other materials in the near infrared (NIR) wavelength range is avoided and LMRs can be obtained in a broadband range from 400 to 1700 nm, which permitted to observe the better performance in the NIR region compared to the visible region: the sensitivity to humidity is improved by more than a factor of two. However, copper oxide is not adequate for sensing humidity. The sensitivity of the device was optimized initially with a tin oxide coating and later with an additional layer of agarose, specifically adequate for the detection of humidity. The best performance was obtained with an agarose concentration 1% w/v, which permitted to observe a 10-fold sensitivity increase compared to the same device without agarose. This opens the path towards the development of environmental, chemical or biological sensors with an optimized sensitivity to a specific parameter to detect.
Embargo
Ag@Fe3O4-coated U-shaped plastic optical fiber sensor for H2S detection
(Elsevier, 2024) López Vargas, Juan David; Dante, Alex; Allil, Regina C.; Del Villar, Ignacio; Matías Maestro, Ignacio; Werneck, Marcelo M.; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This work presents the fabrication of U-shaped plastic optical fiber (POF) sensors for hydrogen sulfide (H2S) detection, coated with Fe3O4 nanoparticles synthetized using the Pulsed Laser Ablation in Liquid (PLAL) technique. The Fe3O4 nanoparticles were synthetized in ultra-pure water and in silver nitrate solution, resulting in two colloidal samples with different morphological, optical, and structural properties. The Fe3O4 nanoparticles were coated onto one POF sensor, while the other sensor was coated with a nanostructure composed of Ag as the core and Fe3O4 as the shell (Ag@Fe3O4). The performance of both sensors was evaluated by exposing them to different concentrations of H2S and other gases such as CH4, H2, and CO2. All experiments were conducted at 25 °C. Results showed that the sensor coated with Ag@Fe3O4 was 12 times more sensitive to H2S compared to the sensor coated with Fe3O4, with a detection limit of 1 ppm and a rise time of 15 s. Moreover, the POF sensor coated with Ag@Fe3O4 presented high selectivity to H2S, making it a promising candidate for H2S detection in different applications. The sensor's performance was also evaluated with a relative humidity range of 20–90%, exhibiting a minimal 0.75% signal variation at 90% humidity.
Open Access
Optimization of fiber Bragg gratings inscribed in thin films deposited on D-shaped optical fibers
(MDPI, 2021) Imas González, José Javier; Ruiz Zamarreño, Carlos; Del Villar, Ignacio; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
A fiber Bragg grating patterned on a SnO2 thin film deposited on the flat surface of a D-shaped polished optical fiber is studied in this work. The fabrication parameters of this structure were optimized to achieve a trade-off among reflected power, full width half maximum (FWHM), sensitivity to the surrounding refractive index (SRI), and figure of merit (FOM). In the first place, the influence of the thin film thickness, the cladding thickness between the core and the flat surface of the D-shaped fiber (neck), and the length of the D-shaped zone over the reflected power and the FWHM were assessed. Reflected peak powers in the range from −2 dB to −10 dB can be easily achieved with FWHM below 100 pm. In the second place, the sensitivity to the SRI, the FWHM, and the FOM were analyzed for variations of the SRI in the 1.33–1.4 range, the neck, and the thin-film thickness. The best sensitivities theoretically achieved for this device are next to 40 nm/RIU, while the best FOM has a value of 114 RIU−1.
Open Access
A comprehensive study of optical resonances in metals, dielectrics, and excitonic materials in double interface structures
(Elsevier, 2025-02-01) Imas González, José Javier; Matías Maestro, Ignacio; Del Villar, Ignacio; Ozcariz Celaya, Aritz; Vitoria Pascual, Ignacio; Ruiz Zamarreño, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
From an optical perspective, depending on the relationship between the real (n) and imaginary (k) parts of its refractive index, three broad categories of materials can be distinguished: metals (k ¿ n), dielectrics (n ¿ k), and materials in which n ¿ k (termed here excitonic materials). The modes and optical resonances that appear in a thin film bounded by two dielectrics with similar refractive index, what we call here a double interface structure, have been widely studied in the case of metals, but not for dielectrics, or materials with n ¿ k. In this work, we propose a new approach, based on employing the phase matching condition to correlate the resonances that appear in the wavelength versus incident angle color maps of the reflected power with the modal analysis of the cross section of the structure. This analysis is performed, using an attenuated total reflection (ATR) setup, for thin film materials that belong to each of the mentioned categories: a metal (gold, Au), a dielectric (titanium dioxide, TiO2), and a material with n ¿ k (chromium, Cr). The theoretical analysis is supported with experimental results. It is demonstrated that this method enables to identify any resonance at any wavelength or incident angle, being valid for all three types of materials. Therefore, it is considered the suggested approach will help the research in these materials and in the double interface structure in the optics and photonics field.
Open Access
Fiber-based label-free D-dimer detection for early diagnosis of venous thromboembolism
(SPIE, 2020) Zubiate Orzanco, Pablo; Urrutia Azcona, Aitor; Ruiz Zamarreño, Carlos; Fernández Irigoyen, Joaquín; Giannetti, Ambra; Baldini, Francesco; Díaz Lucas, Silvia; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Santamaría Martínez, Enrique; Del Villar, Ignacio; Chiavaioli, Francesco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
D-dimer is a useful diagnostic biomarker for deep vein thrombosis or pulmonary embolism, collectively referred to as venous thromboembolism (VTE). The ability to detect in real-time the amount of D-dimer with a fast and reliable method is a key step to anticipate the appearance of these diseases. The combination of fiber-optic-based platforms for biosensing with the nanotechnologies is opening up the chance for the development of in situ, portable, lightweight, versatile, reliable and high-performance optical sensing devices towards lab-on-fiber technology. The generation of lossy mode resonances (LMRs) by means of the deposition of nm-thick absorbing metal-oxide films on special geometric-modified fibers allows measuring precisely and accurately surface refractive index changes, which are due to the binding interaction between a biological recognition element and the analyte under investigation. This approach enhances the light-matter interaction in a strong way, thus turning out to be more sensitive compared to other optical technology platforms, such as fiber gratings or surface plasmon resonance. Here, the results of a highly specific and sensitive biosensor for the detection of D-dimer based on LMR in fiber-optics are presented by monitoring in real-time the shift of the LMR related to the biomolecule interactions thanks to a conventional wavelength-interrogation system and an ad-hoc developed microfluidics. A detection limit of 100 ng/mL, a value 5-fold below the clinical cutoff value, has been attained for D-dimer spiked in human serum. The comparison of the results achieved with proteomics-based methodologies, which allows for the identification of betaand gamma-chains of fibrinogen, demonstrates the ability of our platform to specifically (>90%) recognize D-dimer.
Open Access
Generation of lossy mode resonances (LMR) using perovskite nanofilms
(Chinese Academy of Sciences, 2024) Armas, Dayron; Matías Maestro, Ignacio; López-González, M. Carmen; Ruiz Zamarreño, Carlos; Zubiate Orzanco, Pablo; Del Villar, Ignacio; Romero, Beatriz; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
The results presented here show for the first time the experimental demonstration of the fabrication of lossy mode resonance (LMR) devices based on perovskite coatings deposited on planar waveguides. Perovskite thin films have been obtained by means of the spin coating technique and their presence was confirmed by ellipsometry, scanning electron microscopy, and X-ray diffraction testing. The LMRs can be generated in a wide wavelength range and the experimental results agree with the theoretical simulations. Overall, this study highlights the potential of perovskite thin films for the development of novel LMR-based devices that can be used for environmental monitoring, industrial sensing, and gas detection, among other applications.
Open Access
Interdigital concept in photonic sensors based on an array of lossy mode resonances
(Nature Research, 2021) Domínguez Rodríguez, Ismel; Del Villar, Ignacio; Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Multi-parameter detection is key in the domain of sensors. Here it is demonstrated that an indium tin oxide (ITO) nanocoating can be used to generate multiple lossy mode resonances (LMRs) in the optical spectrum. To achieve this, a nanocoating with a gradient in thickness is generated on the surface of a planar waveguide, permitting broadening of the LMR because the position of an LMR in the optical spectrum is directly related to the nanocoating thickness. The nanocoating with a gradient in thickness contributes multiple LMRs, each one centred at a different wavelength. With a further etching or deposition using a mask, a pattern of deposited and non-deposited regions can be created, resulting in isolation of the LMRs by preventing LMR overlap. This enables tracking of each central wavelength separately, which can be tuned through control of the gradient or nanocoating pattern. The array of LMR-based sensors is a photonics analogue to the interdigital concept in electronics, enabling multiple resonances to be used for multiparameter sensing.