Open Access
Nanocoated optical fibre for lossy mode resonance (LMR) sensors and filters
(IEEE, 2015) Del Villar, Ignacio; Arregui San Martín, Francisco Javier; Corres Sanz, Jesús María; Bariáin Aisa, Cándido; Goicoechea Fernández, Javier; Ruiz Zamarreño, Carlos; Elosúa Aguado, César; Hernáez Sáenz de Zaitigui, Miguel; Rivero Fuente, Pedro J.; Socorro Leránoz, Abián Bentor; Urrutia Azcona, Aitor; Sánchez Zábal, Pedro; Zubiate Orzanco, Pablo; López Torres, Diego; Acha Morrás, Nerea de; Ascorbe Muruzabal, Joaquín; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
Nanometer scale coatings with a complex refractive index deposited on optical fibre permit to obtain attenuation bands in the transmission spectrum, whose central wavelength coincides with the moment when a mode guided in the optical fibre cladding starts to be guided in the coating. Due to the complex refractive index of the coating, the guided mode is a lossy mode. Consequently, these attenuation bands receive the name of lossy mode resonances. This phenomenon can be used for development of ultra-high sensitivity photonic devices (for detection, among others, of volatile organic compounds, pH and refractive index) or for optical filtering. In this work, rules for adequate design are indicated based on numerical results obtained with FIMMWAVE and on experimental results that corroborate the theoretical predictions.
Open Access
Lossy mode resonance sensors based on tungsten oxide thin films
(IEEE, 2020) Del Villar, Ignacio; Bohórquez Navarro, Dina Luz; Caputo, Domanico; Buzzin, Alessio; Chiavaioli, Francesco; Baldini, Francesco; Ruiz Zamarreño, Carlos; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Tungsten oxide (WO3) thin-films fabricated on glass slides have been proven to generate lossy mode resonances (LMRs) in the visible region. Obtained devices were characterized in transmission by lateral incidence of light on the edge of glass slides. Resonances at both TE and TM polarizations were analyzed for different thicknesses and in different deposition conditions. Moreover, it was successfully proved that WO3 coated glass slides present a high sensitivity to refractive index, which opens the path to the application of this structure in the domain of optical sensors.
Open Access
Optical fiber vacuum sensor based on modal interferometer and PDMS coating
(IEEE, 2019) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This work studies the behavior of polydimethylsiloxane (PDMS) as a transducer for optical vacuum pressure measurements. The optical structure chosen for this device is a modal interferometer achieved by splicing a coreless multimode optical fiber between two single mode fibers. Then, an etching process is applied to the obtained device, in order to decrease the diameter of the fiber and increase the sensitivity. Finally, the fiber is coated by dip-coating with a layer of PDMS, which changes its volume with pressure changes. The device has been studied in the 1x10(-3) mbar to 10 mbar range with a wavelength shift of 4 nm. A maximum sensitivity of 35 nm/mbar was obtained. The simple fabrication process, which can be applied to more sensitive structures, suggest that PDMS can be a good choice for the development of optical fiber vacuum sensors.
Embargo
Biosensing based on lossy mode resonances
(Elsevier, 2024-01-01) Matías Maestro, Ignacio; Imas González, José Javier; Ruiz Zamarreño, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Lossy mode resonance (LMR)-based sensors have experienced an important development in the last decade. Among the different domains in which LMR-based sensors have been used, biosensing is one of the fields that has attracted more interest in recent years. Here, LMR properties and some biosensing concepts are reviewed in the first place. Then, the progress of LMR-based biosensors is described, starting with cladding-removed multimode fibers (CRMMF), and evolving towards the employment of D-shaped single mode fibers, which have led to better biosensors in terms of performance and limit of detection (LOD). More recent advances, such as the development of biosensors that combine the optical and electrochemical domains, or the introduction of planar waveguides as the biosensor substrate, are also discussed. In all the cases, examples of biosensors are included, indicating the detected biomarker, biofunctionalization protocol, dynamic range, LOD, and specificity assays. Finally, some conclusions about LMR-based biosensors are presented, as well as future perspectives and some ideas to advance in this field.
Open Access
Optical fiber vacuum sensor based on etched SMS structure and PDMS coating
(IEEE, 2020) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Corres Sanz, Jesús María; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, an optical fiber vacuum sensor based on a single-mode multimode single-mode (SMS) structure coated with polydimethylsiloxane (PDMS) is studied. The SMS structure generates an interferometric pattern based on multimode interference. The structure is dip-coated with a layer of PDMS, whose optical properties change when it is subjected to varying vacuum pressure. Different strategies are applied in an attempt to improve the final performance of the sensor, such as decreasing the diameter of the fiber and modifying the properties of the coating by modifying the proportion of solvent. Decreasing the diameter of the optical fiber and using toluene as a solvent are both proved to be successful strategies for increasing the sensitivity of the sensor. The devices are studied in the 1×10-3–10 mbar range with a maximum wavelength shift of 12 nm, leading to a maximum sensitivity of 35 nm/mbar. The simplicity of the fabrication process, which can be applied to more sensitive structures, suggests that PDMS may be a good choice for the development of optical fiber vacuum sensors.
Open Access
Temperature sensor using a multiwavelength erbium-doped fiber ring laser
(Hindawi, 2017) Díaz Lucas, Silvia; San Fabián García, Noé; Socorro Leránoz, Abián Bentor; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
A novel temperature sensor is presented based on a multiwavelength erbium-doped fiber ring laser.The laser is comprised of fiber Bragg grating reflectors as the oscillation wavelength selecting filters.The performance of the temperature sensor in terms of both wavelength and laser output power was investigated, as well as the application of this systemfor remote temperaturemeasurements.
Open Access
Highly sensitive sensor for measuring material thermal expansion using a ring laser
(IEEE, 2023) Díaz Lucas, Silvia; Fuentes Lorenzo, Omar; Torres Betancourt, Angie Tatiana; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A new thermal expansion sensor is presented in this letter. It combines an interferometric fiber sensor and an erbium-doped fiber ring laser as the light source. The sensor consists of a combination of single-mode, hollow-core, and no-core mirror fibers. The sensor was tested on two different types of based metal, such as aluminum and steel, giving sensitivities as high as 38.7 and 5.75 nm/°C, respectively, showing good performance.
Open Access
Fault detection of planetary gears based on signal space constellations
(MDPI, 2022) Martincorena Arraiza, Maite; Cruz Blas, Carlos Aristóteles de la; López Martín, Antonio; Molina Vicuña, Cristian; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
A new method to process the vibration signal acquired by an accelerometer placed in a planetary gearbox housing is proposed, which is useful to detect potential faults. The method is based on the phenomenological model and consists of the projection of the healthy vibration signals onto an orthonormal basis. Low pass components representation and Gram–Schmidt’s method are conveniently used to obtain such a basis. Thus, the measured signals can be represented by a set of scalars that provide information on the gear state. If these scalars are within a predefined range, then the gear can be diagnosed as correct; in the opposite case, it will require further evaluation. The method is validated using measured vibration signals obtained from a laboratory test bench.
Open Access
Electrochemical lossy mode resonance for the detection of manganese ions
(Elsevier, 2023) Domínguez Rodríguez, Ismel; Corres Sanz, Jesús María; Del Villar, Ignacio; Mozo, Juan D.; Simerova, Radka; Sezemsky, Petr; Stranak, Vitezslav; Smietana, Mateusz; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work we propose electrochemical lossy mode resonance (eLMR) as a powerful method for the detection of manganese (Mn) ions. The sensor is based on a simple planar waveguide (sodasingle bondlime glass coverslip) coated with a thin layer of indium tin oxide (ITO) to obtain an optical resonance effect. Simultaneously, the ITO layer served as the working electrode in the cathodic stripping voltammetry (CSV) of Mn. The eLMR sensor is capable of simultaneously performing electrochemical (EC) and optical measurements, specifically lossy mode resonance (LMR), to monitor the growth of the adsorbed Mn layer on the ITO electrode and the electrochemically modulated diffusion layer. For Mn2+ ions, a limit of detection (LoD) of 1.26 ppb has been demonstrated using the EC method, whereas the optical method exhibited a LoD of 67.76 ppb. The results obtained indicate significant potential for application in molecular electrochemistry and studies focused on electrified interfaces.
Open Access
Trends in the design of intensity-based optical fiber biosensors (2010–2020)
(MDPI, 2021) Acha Morrás, Nerea de; Socorro Leránoz, Abián Bentor; Elosúa Aguado, César; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua
There exists an increasing interest in monitoring low concentrations of biochemical species, as they allow the early-stage detection of illnesses or the monitoring of the environment quality. Thus, both companies and research groups are focused on the development of accurate, fast and highly sensitive biosensors. Optical fiber sensors have been widely employed for these purposes because they provide several advantages for their use in point-of-care and real-time applications. In particular, this review is focused on optical fiber biosensors based on luminescence and absorption. Apart from the key parameters that determine the performance of a sensor (limit of detection, sensibility, cross-sensibility, etc.), other features are analyzed, such as the optical fiber dimensions, the sensing set ups and the fiber functionalization. The aim of this review is to have a comprehensive insight of the different aspects that must be taken into account when working with this kind of sensors.