Person:
Biurrun Quel, Carlos

person.page.identifierURI

https://academica-e.unavarra.es/handle/2454/48730

Last Name

Biurrun Quel

First Name

Carlos

person.page.departamento

Ingeniería Eléctrica, Electrónica y de Comunicación

ORCID

0000-0001-6446-3248

person.page.upna

811367

Full item page

Search Results

Now showing 1 - 10 of 19

Open Access
Photonic-assisted 2-D terahertz beam steering enabled by a LWA array monolithically integrated with a BFN
(Optica, 2022) Haddad, Thomas; Biurrun Quel, Carlos; Lu, Peng; Tebart, Jonas; Sievert, Benedikt; Makhlouf, Sumer; Grzeslo, Marcel; Teniente Vallinas, Jorge; Río Bocio, Carlos del; Stöhr, Andreas; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A novel photonic-assisted 2-D Terahertz beam steering chip using only two tuning elements is presented. The chip is based on an array of three leaky wave antennas (LWAs) with a monolithically integrated beamforming network (BFN) on a 50 µm-thick indium phosphide substrate. The THz beam angle in elevation (E-plane) is controlled via optical frequency tuning using a tunable dual-wavelength laser. An optical delay line is used for azimuth (H-plane) beam control. The simulated beam scanning range is 92° in elevation for a frequency sweep from 0.23 THz to 0.33 THz and 69.18° in azimuth for a time delay of 3.6 ps. For the frequency range from 0.26 THz to 0.32 THz, it is confirmed experimentally that the THz beam scans from −12° to +33°, which is in good agreement with the numerical simulations. The beam direction in azimuth scans with a total angle of 39° when applying a delay difference of 1.68 ps. A good agreement is found between theoretically predicted and experimentally determined THz beam angles with a maximum angle deviation below 5°. The experimental scanning angles are limited due to the mechanical constraints of the on-wafer probes, the on-chip integrated transition and the bandwidth of the THz receiver LNA. The mechanical limitation will be overcome when using a packaged chip.
Open Access
Multi-channel feedarray reflector antenna based radar concept for HRWS SAR imaging
(IEEE, 2021) Castillo, Javier del; Orgaz, Lara; García, Quiterio; Memeletzoglou, Nafsika; Toso, Giovanni; Imbembo, Ernesto; Biurrun Quel, Carlos; Río Bocio, Carlos del; Institute of Smart Cities - ISC
Large deployable reflector based multi-channel antenna systems are a key component of next generation SAR missions as they allow implementing multi-beam imaging capabilities and provide an efficient way to overcome the classical SAR resolution-coverage trade-off, covering wide swaths with high azimuth resolution. The presented work shows the design of a multichannel L-band SAR system and antenna architecture based on different feeders concepts and capable to map 400 km ground swath with 5 meter spatial resolution in dual polarization. The paper describes a preliminary design and architecture of the SAR system and the antenna where different design aspects including beamforming concepts and feedarray implementation techniques have been identified and assessed in view of achieving the required SAR performances while reducing the overall complexity of the solution.
Open Access
Design and characterization of terahertz CORPS beam forming networks
(Springer, 2023) Biurrun Quel, Carlos; Haddad, Thomas; Sievert, Benedikt; Kress, Robin; Weimann, Nils; Erni, Daniel; Rennings, Andreas; Stöhr, Andreas; Teniente Vallinas, Jorge; Río Bocio, Carlos del; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This work reviews the design and applicability of beam-forming networks based on Coherently Radiating Periodic Structures (CORPS-BFN) at Terahertz (THz) frequency bands. These versatile networks offer two operation modes: a continuous beam steering – feeding an antenna array with a linearly progressive phase distribution – using a reduced number of phase controls; or a multi-beam operation, generating independent, overlapped beams. These networks are built upon the concatenation of power combiners/dividers (PCDs) with isolated outputs. The isolation is provided by monolithically integrated resistors, implemented with Ti/TiO thin films for the first time. In this work, a planar prototype of a (inputs/outputs) microstrip CORPS-BFN for operation in the WR3.4/WM-864 band (220–330 GHz) on a thin 50 m Indium Phosphide (InP) substrate is designed, fabricated, and characterized. The measured S-parameters show a reflection coefficient better than -15 dB and an insertion loss between 1.6 and 3.2 dB in the whole band. In addition, an isolation better than 20 dB between the input ports has been measured. An overall remarkable agreement is observed between the measurements and the simulations. Last, the applications, scalability and efficiency of this type of networks at the targeted band are discussed in detail.
Open Access
New hexagonal CORPS-BFN for multibeam antenna applications
(IEEE, 2020) Biurrun Quel, Carlos; Montesano, Antonio; Ederra Urzainqui, Íñigo; Iriarte Galarregui, Juan Carlos; Río Bocio, Carlos del; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This work presents a new topology of a Coherently Radiating Periodic Structure - Beam Forming Network (CORPS-BFN) and its application for multibeam systems. A unit cell, consisting of a transition from a coaxial input to an intersection of three strip-lines with an angular span of 120 degrees, is proposed and analysed. A periodical replication of the cell gives rise to a uniform layer, allowing a proper matching of the ports of the network. Stacked layers allow in-phase propagation and distribution of the energy through the structure, increasing the number of output ports with each layer.
Open Access
Noise in coherently radiating periodic structures beam forming networks
(IEEE, 2022) Biurrun Quel, Carlos; Río Bocio, Carlos del; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Following the noise wave theory, beam forming networks based on Coherently Radiating Periodic Structures (CORPS-BFN) are analysed and proven to be capable of enhancing the Signal to Noise Ratio of the system by analogically multiplexing the signal and noise contributions present at every input port. The geometry of the network determines the maximum enhancement achievable, which is demonstrated to be independent from insertion losses. These findings are supported by a mathematical approach, as well as with experimental data.
Open Access
High saturation photocurrent THz waveguide-type MUTC-photodiodes reaching mW output power within the WR3.4 band
(Optica, 2023) Grzeslo, Marcel; Dülme, Sebastián; Clochiatti, Simone; Neerfeld, Tom; Haddad, Thomas; Lu, Peng; Tebart, Jonas; Makhlouf, Sumer; Biurrun Quel, Carlos; Fernández Estévez, José Luis; Lackmann, Jörg; Weimann, Nils; Stöhr, Andreas; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, we report on waveguide-type modified uni-traveling-carrier photodiodes (MUTC-PDs) providing a record high output power level for non-resonant photodiodes in the WR3.4 band. Indium phosphide (InP) based waveguide-type 1.55 µm MUTC-PDs have been fabricated and characterized thoroughly. Maximum output powers of −0.6 dBm and −2.7 dBm were achieved at 240 GHz and 280 GHz, respectively. This has been accomplished by an optimized layer structure and doping profile design that takes transient carrier dynamics into account. An energy-balance model has been developed to study and optimize carrier transport at high optical input intensities. The advantageous THz capabilities of the optimized MUTC layer structure are confirmed by experiments revealing a transit time limited cutoff frequency of 249 GHz and a saturation photocurrent beyond 20 mA in the WR3.4 band. The responsivity for a 16 µm long waveguide-type THz MUTC-PD is found to be 0.25 A/W. In addition, bow-tie antenna integrated waveguide-type MUTC-PDs are fabricated and reported to operate up to 0.7 THz above a received power of −40 dBm.
Open Access
Development of a microscopic driver-centric simulator with Unity3D and SUMO
(2016) Biurrun Quel, Carlos; Serrano Arriezu, Luis Javier; Olaverri Monreal, Cristina; Escuela Técnica Superior de Ingenieros Industriales y de Telecomunicación; Telekomunikazio eta Industria Ingeniarien Goi Mailako Eskola Teknikoa; University of Applied Sciences Technikum Wien (Austria)
Diversas herramientas han sido desarrolladas en el campo de la simulación de tráfico. Estas herramientas permiten recrear situaciones de tráfico complejas de una forma realista, que pueden ser empleadas en la planificación de sistemas de transporte o para evaluar comunicaciones V2V (Vehículo a vehículo) en situaciones reales de tráfico. A pesar de que ciertos trabajos han sido llevados a cabo en el campo de la representación 3D de las simulaciones de tráfico, no existen demasiados ejemplos de plataformas Driver-Centric (con perspectiva del conductor) en los que el comportamiento del resto de vehículos es modelado por un simulador de tráfico. En este Trabajo Fin de Grado se presenta la elaboración de un simulador de tráfico Driver-Centric, capaz de emplear redes de carreteras reales junto con modelos de tráfico realistas, en un escenario 3D. Una librería existente en Java ha sido traducida a .NET y usada en Unity3D para implementar el protocolo TraCI y lograr la comunicación con el programa de simulación microscópica de tráfico, SUMO. Finalmente, se ha evaluado el funcionamiento del simulador y se han presentado futuras líneas de trabajo.
Open Access
Hexagonal CORPS-BFN to feed OLAF SAR instrument
(IEEE, 2021) Biurrun Quel, Carlos; Iriarte Galarregui, Juan Carlos; Ederra Urzainqui, Íñigo; Río Bocio, Carlos del; Institute of Smart Cities - ISC
The concept of Coherently Radiating Periodic Structures-based Beam Forming Networks is applied to feed OLAF (OverLapped SubArray Fed) antenna for SAR Instrument at L-Band. The proper feeding of this system requires the multiple beams to be highly overlapped, and that is generated by a CORPS-BFN using a new 4-port Gysel power combiner/divider implemented in a suspended stripline technology. The network provides high isolation between inputs/outputs, low insertion loss, great return loss and the desired ovelapping of the different beams.
Open Access
Suppressing open stopband for terahertz periodic microstrip leaky-wave antennas
(IEEE, 2023) Haddad, Thomas; Biurrun Quel, Carlos; Lu, Peng; Kaya, Hacer; Mohammad, Israa; Stöhr, Andreas; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper reports on a periodic microstrip Leaky-wave antenna (LWA). The open stopband issue is suppressed by altering the unit cell using a matching stub. The developed LWA is based on a grounded InP-substrate of 50 µm and has been fabricated and characterized between 0.23 to 0.33 THz. The dispersion diagram of the designed unit cell shows enhancement of the attenuation constant at the broadside frequency of 0.273 THz and about 50% less deflection at the broadside region on the Bloch impedance curves, consequently better impedance matching at the input. The simulated scattering parameters of the proposed LWA show that the return loss S11 is below 17 dB except for the broadside, which has a value of 13.8 dB. Furthermore, the beam steering capabilities of the antenna are simulated in the WR3.4 band and confirmed experimentally between 0.26 and 0.33 THz proving the beam direction to steer from −12° to +33°, respectively.
Open Access
Characterization of 3D-printed choke horn antenna for 5G backhaul applications
(IEEE, 2019) Biurrun Quel, Carlos; Lacombe, Elsa; Gianesello, Frederic; Luxe, Cyril; Río Bocio, Carlos del; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
The 200 and 320 GHz frequency band constitutes an interesting window with approximately constant attenuation, which could potentially have applications in the area of ultrahigh-capacity wireless links. The user's demand of data for future 5G mobile systems will require backhaul systems to be able to provide several dozens of GHz in order to satisfy those demands. Furthermore, additive manufacturing techniques stand as an interesting way of reducing costs without sacrificing performance. In this work, a choke horn antenna, designed at a central frequency of 240 GHz and manufactured by 3D-printing technology is presented. This antenna is thought to serve as the feed of a compact parabolic reflector. The antenna has been measured by Near- and Far-Field techniques and these measurements show an adequate agreement with simulation results. Additionally, the measurement set-up included a novel dynamic time-domain, software-controlled gating that readjusts itself for every measured point.