Open Access
Diseño y desarrollo de estructuras ópticas para la fabricación de sensores de fibra óptica
(2018) Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa; Gobierno de Navarra / Nafarroako Gobernua, 2017/PI044
Actualmente existe una gran variedad de opciones para el sensado mediante métodos ópticos y, más concretamente, para el desarrollo de sensores utilizando fibra óptica. Aunque la mayoría de los principios físicos utilizados para el desarrollo este tipo de sensores ya han sido ampliamente estudiados, se siguen desarrollando nuevos métodos que faciliten su fabricación o que mejoren sus características. Gracias a una mayor accesibilidad a nuevas tecnologías para la manipulación de la fibra óptica, un mayor conocimiento de las técnicas para la deposición de recubrimientos de espesor nanométrico y el estudio de nuevos materiales, la investigación en este campo continúa siendo de gran interés y sigue ofreciendo resultados novedosos. Esta tesis estudia la generación de fenómenos ópticos mediante un material que actúa a la vez como capa sensible a un parámetro de interés, con el objetivo de mejorar la sensibilidad de este tipo de dispositivos mediante métodos de fabricación asequibles y repetitivos. Como fenómenos ópticos se han estudiado interferómetros Fabry-Pérot, redes de difracción de Bragg, redes de difracción de periodo largo y resonancias de modos con pérdidas. Los interferómetros Fabry-Pérot, estudiados para el sensado de humedad y detección de gases, fueron el paso previo para el desarrollo posterior de redes de difracción de Bragg en punta de fibra. Estas fueron fabricadas mediante el uso de un único material cuyas constantes ópticas se modificaron mediante la variación de los parámetros del proceso de deposición. Las redes de difracción de periodo largo fueron desarrolladas en fibra monomodo estándar estrechada con ácido, mediante la ablación láser periódica de un nano-recubrimiento depositado previamente. En el caso de las resonancias de modos con pérdidas, se estudió su generación en fibra monomodo con cladding reducido mediante ataque químico con ácido, así como su utilización en aplicaciones no estudiadas previamente, como son sensores de campo magnético o filtros sintonizables eléctricamente.
Open Access
Optical sensors based on lossy-mode resonances
(Elsevier Science, 2017) Matías Maestro, Ignacio; Ascorbe Muruzabal, Joaquín; Acha Morrás, Nerea de; López Torres, Diego; Zubiate Orzanco, Pablo; Sánchez Zábal, Pedro; Urrutia Azcona, Aitor; Socorro Leránoz, Abián Bentor; Rivero Fuente, Pedro J.; Hernáez Sáenz de Zaitigui, Miguel; Elosúa Aguado, César; Goicoechea Fernández, Javier; Bariáin Aisa, Cándido; Corres Sanz, Jesús María; Ruiz Zamarreño, Carlos; Arregui San Martín, Francisco Javier; Del Villar, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC
Open Access
Planar-waveguide-lmr-based sensors: engineering the depth of characteristic curves
(IEEE, 2023) Shrivastav, Anand M.; Del Villar, Ignacio; Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Lossy mode resonance (LMR)-based sensors have been proven as one of the exponentially growing research fields since the last decade. These sensors have demonstrated their capabilities in the detection of several physical, chemical, and biological entities, such as refractive index, humidity, gases, enzymes, etc. Conventionally, LMR-based sensors are developed using optical fiber as the sensing platform, but to increase the broad range of applications and better tenability, planar waveguide substrates for LMR realization have been introduced in the last few years. This provides a greater degree of freedom for the sensor design such as tunability in substrate thickness, material, and better surface immobilization. The current study focuses on evaluating the effect of substrate thickness on LMR-based optical sensors to achieve higher sensing performance. For experiments, 150-μm-thick glass coverslips are used as the thin planer substrate, which is then coated with a few nanometers thick LMR-supported SnO 2 layer using the dc sputtering method. Furthermore, to monitor the effect of the changing substrate thickness, the width of the glass coverslip is reduced through the chemical etching process using the 40% HF solution, and simultaneously, the changes in LMR spectra are analyzed. The study shows that the depth of LMR curves strongly depend on the thickness of the waveguide providing LMRs with lower substrate thickness possesses higher depth. Greater depth in LMR curves is a crucial factor in identifying the minimum transmission wavelength of resonance, making it easier to track and detect the targeted parameter. This characteristic greatly enhances the applicability of LMR-based sensors in industrial applications.
Open Access
Recent developments in fiber optics humidity sensors
(MDPI, 2017) Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
A wide range of applications such as health, human comfort, agriculture, food processing and storage, and electronic manufacturing, among others, require fast and accurate measurement of humidity. Sensors based on optical fibers present several advantages over electronic sensors and great research efforts have been made in recent years in this field. The present paper reports the current trends of optical fiber humidity sensors. The evolution of optical structures developed towards humidity sensing, as well as the novel materials used for this purpose, will be analyzed. Well-known optical structures, such as long-period fiber gratings or fiber Bragg gratings, are still being studied towards an enhancement of their sensitivity. Sensors based on lossy mode resonances constitute a platform that combines high sensitivity with low complexity, both in terms of their fabrication process and the equipment required. Novel structures, such as resonators, are being studied in order to improve the resolution of humidity sensors. Moreover, recent research on polymer optical fibers suggests that the sensitivity of this kind of sensor has not yet reached its limit. Therefore, there is still room for improvement in terms of sensitivity and resolution.
Open Access
Humidity sensor based on Bragg gratings developed on the end facet of an optical fiber by sputtering of one single material
(MDPI, 2017) Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The refractive index of sputtered indium oxide nanocoatings has been altered just by changing the sputtering parameters, such as pressure. These induced changes have been exploited for the generation of a grating on the end facet of an optical fiber towards the development of wavelength-modulated optical fiber humidity sensors. A theoretical analysis has also been performed in order to study the different parameters involved in the fabrication of this optical structure and how they would affect the sensitivity of these devices. Experimental and theoretical results are in good agreement. A sensitivity of 150 pm/%RH was obtained for relative humidity changes from 20% to 60%. This kind of humidity sensors shows a maximum hysteresis of 1.3% relative humidity.
Open Access
Optical fiber vacuum sensor based on modal interferometer and PDMS coating
(IEEE, 2019) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This work studies the behavior of polydimethylsiloxane (PDMS) as a transducer for optical vacuum pressure measurements. The optical structure chosen for this device is a modal interferometer achieved by splicing a coreless multimode optical fiber between two single mode fibers. Then, an etching process is applied to the obtained device, in order to decrease the diameter of the fiber and increase the sensitivity. Finally, the fiber is coated by dip-coating with a layer of PDMS, which changes its volume with pressure changes. The device has been studied in the 1x10(-3) mbar to 10 mbar range with a wavelength shift of 4 nm. A maximum sensitivity of 35 nm/mbar was obtained. The simple fabrication process, which can be applied to more sensitive structures, suggest that PDMS can be a good choice for the development of optical fiber vacuum sensors.
Open Access
Gas detection using LMR-based optical fiber sensors
(MDPI, 2018) Dreyer, Uilian José; Ozcariz Celaya, Aritz; Ascorbe Muruzabal, Joaquín; Zubiate Orzanco, Pablo; Vitoria Pascual, Ignacio; Martelli, Cicero; Cardozo da Silva, Jean Carlos; Ruiz Zamarreño, Carlos; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This work presents a first approach to the utilization of Lossy Mode Resonance (LMR) based optical fiber sensors for gas detection. The optical sensor is based on a SnO2 thin-film fabricated onto the core of cladding removed multimode fibers (MMF). The time response of the device to four different gases (NH3, NO, CO2 and O2) was monitored obtaining the best sensitivity for NO whereas the response to NH3 revealed the best repeatability.
Open Access
Optical fiber vacuum sensor based on etched SMS structure and PDMS coating
(IEEE, 2020) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Corres Sanz, Jesús María; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, an optical fiber vacuum sensor based on a single-mode multimode single-mode (SMS) structure coated with polydimethylsiloxane (PDMS) is studied. The SMS structure generates an interferometric pattern based on multimode interference. The structure is dip-coated with a layer of PDMS, whose optical properties change when it is subjected to varying vacuum pressure. Different strategies are applied in an attempt to improve the final performance of the sensor, such as decreasing the diameter of the fiber and modifying the properties of the coating by modifying the proportion of solvent. Decreasing the diameter of the optical fiber and using toluene as a solvent are both proved to be successful strategies for increasing the sensitivity of the sensor. The devices are studied in the 1×10-3–10 mbar range with a maximum wavelength shift of 12 nm, leading to a maximum sensitivity of 35 nm/mbar. The simplicity of the fabrication process, which can be applied to more sensitive structures, suggests that PDMS may be a good choice for the development of optical fiber vacuum sensors.
Open Access
Fabrication of long period gratings by periodically removing the coating of cladding-etched single mode optical fiber towards optical fiber sensor development
(MDPI, 2018) Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Del Villar, Ignacio; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua, 2017/PI044
Here, we present a novel method to fabricate long period gratings using standard single mode optical fibers (SMF). These optical devices were fabricated in a three-step process, which consisted of etching the SMF, then coating it with a thin-film and, the final step, which involved removing sections of the coating periodically by laser ablation. Tin dioxide was chosen as the material for this study and it was sputtered using a pulsed DC sputtering system. Theoretical simulations were performed in order to select the appropriate parameters for the experiments. The responses of two different devices to different external refractive indices was studied, and the maximum sensitivity obtained was 6430 nm/RIU for external refractive indices ranging from 1.37 to 1.39.
Open Access
Dual-cavity fiber fabry-perot interferometer coated with SnO2for relative humidity and temperature sensing
(IEEE, 2020) Domínguez Flores, Carmen E.; Rodríguez-Quiroz, Osvaldo; Monzón-Hernández, David; Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
An optical fiber tip interferometer for the measurement of relative humidity (RH) and temperature is proposed. The optical fiber structure used, a dual-cavity optical fiber Fabry-Perot interferometer (DFFPI), is simply-to-fabricate, compact, and robust. The reflectance (RDFFPI) of the interferometer is sensitive to the refractive index (RI) and temperature of the external medium. Consequently, when the cross-section of the fiber tip was coated with a SnO 2 thin film, whose RI changes according to the humidity of the surrounding ambient, the measurement of the RH was possible. An increment of the RH produced a decrement of RI of the SnO 2 thin film, then the reflectance of the fiber tip end-face diminished, and this produced a decrement of the visibility of the interference fringes. The analysis of the RDFFPI was carried out in the Fourier domain, using a novel processing method it was possible to establish that the amplitude of two peaks of Fourier spectrum changed at a ratio of 39.49 × 10 -3 %RH -1 in the range of 40 to 90 RH%. On the other hand, the temperature of the humidity chamber was monitored, from 25 to 60 °C at a fixed RH%, by analyzing the phase shift of the interference pattern produced by the changes in the optical path length of the cavities. The good sensitivity, stability, reproducibility, and compactness of the fiber tip RH sensor make this proposal very appealing in a wide range of applications.