Open Access
Análisis de la influencia de las condiciones de proceso sobre el acabado superficial de materiales cerámicos fabricados por electroerosión
(CENIM, 2004) Puertas Arbizu, Ignacio; Luis Pérez, Carmelo Javier; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
El mecanizado por electroerosión (en inglés, Electrical Discharge Machining, EDM) constituye una alternativa emergente frente a otros procesos de fabricación de materiales cerámicos conductores, tales como: mecanizado por láser, mecanizado electroquímico, chorro de agua con abrasivos, mecanizado por ultrasonidos y rectificado con muela de diamante. Debido a su interés en el ámbito industrial, en este trabajo se lleva a cabo un estudio de la influencia de las condiciones de operación sobre el aspecto superficial de tres materiales cerámicos conductores: carburo de boro prensado en caliente (B4C), carburo de silicio infiltrado con silicio (SiSiC) y carburo de wolframio en matriz metálica de cobalto (WC-Co), electroerosionados bajo diferentes condiciones de mecanizado y para el caso particular de regímenes de acabado (Ra ≤ 1 μm).
Open Access
EDM machinability and surface roughness analysis of INCONEL 600 using graphite electrodes
(Springer, 2016) Torres Salcedo, Alexia; Puertas Arbizu, Ignacio; Luis Pérez, Carmelo Javier; Ingeniería; Ingeniaritza
Open Access
Optimization and modeling of ZrB2 ceramic processing by EDM for high-performance industrial applications
(Elsevier, 2025-04-11) Luis Pérez, Carmelo Javier; Torres Salcedo, Alexia; Puertas Arbizu, Ignacio; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
This study investigates the Electrical Discharge Machining (EDM) of zirconium diboride (ZrB2), a novel conductive ceramic with exceptional properties, including high temperature resistance, excellent thermal conductivity, and remarkable hardness. These properties make ZrB2 highly suitable for extreme environments, such as aerospace and nuclear applications. To the best of our knowledge, no comprehensive studies have addressed the manufacturing of ZrB2 parts by EDM, positioning this research as a cutting-edge contribution. Two electrode materials, graphite (C) and copper-graphite (Cu–C), were used to analyze the material removal rate (MRR) and surface roughness (Ra) as functions of current intensity (I), pulse time (ti), and duty cycle (η). Multiple Linear Regression (MLR) and Artificial Neural Networks (ANN) were used to model the response variables. While MLR was effective for MRR (R2 > 0.9), ANN outperformed it in predicting Ra, especially for Cu–C electrodes (R2 = 0.9366 vs. 0.3847 for MLR). Current intensity was the most influential parameter for MRR, while pulse time significantly affected Ra. Residual analysis confirmed ANN superior accuracy for Ra, with residuals below ±1 vs. ±2 for MLR. The study culminated in the successful EDM manufacture of a ZrB2 hexagonal nut, employing optimized parameters (I = 6 A, ti = 50 μs, η = 0.3, for the C electrode) derived using ANN models and particle swarm optimization. This result demonstrates the EDM process ability to produce high-precision components with complex geometries, showcasing its versatility and industrial potential. Therefore, this study broadens the understanding of ZrB2 machinability and expands its applications in advanced technologies.
Open Access
Surface roughness analysis on the dry turning of an Al-Cu alloy
(Elsevier, 2015) Torres Salcedo, Alexia; Puertas Arbizu, Ignacio; Luis Pérez, Carmelo Javier; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Nowadays, surface finish has become an important indicator of quality and precision in manufacturing processes and it is considered one of the most important parameter in Industry. In this present study, the influence of different machining parameters on surface roughness has been analyzed. All these parameters have been studied in terms of depth of cut (ap), feed rate (F), cutting speed (Vc) and tool radius (R). A 2030-T4 aluminium alloy has been selected. Moreover, Design of Experiments (DOE) techniques have been used to predict the surface quality in advance and to select the optimal turning conditions. The experimental results revealed that for dry turning operations and for the amplitude parameters, the most significant factor was the interaction effect between the depth of cut and the feed rate. In addition, for facing operations, the feed rate turned out to be the most statistically influential factor of all the surface roughness parameters.
Open Access
Mechanical properties analysis of an Al-Mg alloy connecting rod with submicrometric structure
(MDPI, 2015) León Iriarte, Javier; Salcedo Pérez, Daniel; Murillo Crespo, Óscar; Luis Pérez, Carmelo Javier; Fuertes Bonel, Juan Pablo; Puertas Arbizu, Ignacio; Luri Irigoyen, Rodrigo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Over these last few years, there has been a growing interest in developing mechanical components from submicrometric materials due to the significant improvement that these materials present compared to their original state. This present research work deals with the study of the mechanical properties of a connecting rod isothermally forged from different starting materials. These materials are as follows: annealed aluminum alloy (AA) 5754, the same alloy previously deformed through equal channel angular pressing (ECAP) and a third case where the previously ECAP-processed material is subjected to a recovery heat treatment. A comparison is made between finite volume (FV) simulations and experimental tests with respect to hardness, plastic strain and forging force. Furthermore, the improvement in the mechanical properties of the connecting rod forged from predeformed material is evaluated in comparison to the connecting rod forged with annealed material. The microstructure of both cases is also compared at the end of the manufacturing process.
Open Access
Analysis on the manufacturing of an AA5083 straight blade previously ECAE processed
(Hindawi, 2013) Salcedo Pérez, Daniel; Luis Pérez, Carmelo Javier; Puertas Arbizu, Ignacio; León Iriarte, Javier; Fuertes Bonel, Juan Pablo; Luri Irigoyen, Rodrigo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Over these past few years, there have been a large number of technical papers published related to the problem of improving the mechanical properties of materials obtained through severe plastic deformation. Nevertheless, the number of technical papers dealing with improvement in the mechanical properties of mechanical components manufactured from submicrometric grain size material has not been so proficient. Therefore, in this present research work, a straight blade has been manufactured starting from AA-5083 previously processed by ECAE twice (N2) with route C.This material will be manipulated so as to be isothermally forged at different temperature values.This present research work shows the results that are inherent in an improvement in themechanical properties and the microstructure achieved in the thus obtained components, compared with the starting material. In addition, the optimum forging temperature to achieve these components will be determined. As shown in this research work, it is possible to obtain submicrometric grain size mechanical components with a higher mechanical strength than those obtained in nonultrafine grained materials. The originality of this research work lies in the manufacturing of actual mechanical components from ECAE processed material and the analysis of their properties.
Open Access
Analysis of tribological properties in disks of AA-5754 and AA-5083 aluminium alloys previously processed by equal channel angular pressing and isothermally forged
(MDPI, 2020) Luis Pérez, Carmelo Javier; Luri Irigoyen, Rodrigo; Puertas Arbizu, Ignacio; Salcedo Pérez, Daniel; León Iriarte, Javier; Fuertes Bonel, Juan Pablo; Ingeniería; Ingeniaritza
In the present study, the wear behaviour of two aluminium alloys (AA‐5754 and AA‐5083) is analysed where these have been previously processed by severe plastic deformation (SPD) with equal channel angular pressing (ECAP). In order to achieve the objectives of this study, several disks made of these alloys are manufactured by isothermal forging from different initial states. The microstructures of the initial materials analysed in this study have different accumulated deformation levels. In order to compare the properties of the nanostructured materials with those which have not been ECAP‐processed, several disks with a height of 6 mm and a diameter of 35 mm are manufactured from both aluminium alloys (that is, AA‐5754 and AA‐5083) isothermally forged at temperatures of 150 and 200 °C, respectively. These thus‐manufactured disks are tested under a load of 0.6 kN, which is equivalent to a stress mean value of 18 MPa, and at a rotational speed of 200 rpm. In order to determine the wear values, the disks are weighed at the beginning, at 10,000 revolutions, at 50,000 revolutions and at 100,000 revolutions, and then the volume‐loss values are calculated. This study was carried out using specific equipment, which may be considered to have a block‐on‐ring configuration, developed for testing in‐service wear behaviour of mechanical components. From this, the wear coefficients for the two materials at different initial states are obtained. In addition, a comparison is made between the behaviour of the previously ECAP-processed aluminium alloys and those that are non‐ECAP‐processed. A methodology is proposed to determine wear coefficients for the aluminium alloys under consideration, which may be used to predict the wear behaviour. It is demonstrated that AA‐5754 and AA‐5083 aluminium alloys improve wear behaviour after the ECAP process compared to that obtained in non‐ECAP‐processed materials.
Open Access
Revisión de las aplicaciones de la electroerosión por penetración al mecanizado de cerámicas conductoras
(CENIM, 2002) Puertas Arbizu, Ignacio; Luis Pérez, Carmelo Javier; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
El término de materiales cerámicos técnicos o materiales cerámicos avanzados se aplica a una gama emergente de materiales, que tienen unas propiedades excelentes de dureza, resistencia al desgaste, resistencia mecánica, resistencia a la corrosión, en un amplio rengo de temperatura. Sin embargo, los materiales con buenas prestaciones suelen ser difíciles de procesar y los materiales cerámicos no son la excepción. Aunque la mayor parte de los materiales cerámicos no son conductores, gracias a la utilización de determinados aditivos metálicos es posible hacer que lo sean y, por lo tanto, éstos pueden ser mecanizados por procesos de electroerosión. El presente trabajo es una revisión de las diferentes aplicaciones de los materiales cerámicos, haciéndose especial hincapié en los materiales cerámicos conductores, así como de los procesos de mecanizado que se pueden emplear en su fabricación, incidiendo fundamentalmente sobre el proceso de la electroerosión por penetración.
Open Access
A study on the EDM drilling of reaction-bonded silicon carbide using different electrode materials
(Springer, 2023) Torres Salcedo, Alexia; Luis Pérez, Carmelo Javier; Puertas Arbizu, Ignacio; Corres Sanz, Jesús María; Ingeniería; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Today, there is a growing demand for efficient hole manufacturing technology in many industries such as aeronautics, automotive and nuclear, among others. Thus, the present study deals with the machining of through holes on SiSiC advanced ceramic by using Electrical Discharge Machining (EDM) drilling technology. Since recommendations related to the electrode characteristics and settings parameters are found to be scant for the industrial use of EDM drilling of SiSiC ceramics, this research work comes to cover this gap as it presents a complete study focused on the influence on different electrodes under rough and finish machining conditions. In particular, the influence of four electrodes materials (copper, copper-tungsten, graphite and copper infiltrated graphite) and three different electrode diameters ranging from 2 to 4 mm are investigated. In addition, the rotational speed of the electrode is also analysed. From the experimental results, both electrode material and machining regime, seem to be the most relevant factors of all. In the case of 2 mm diameter electrode, material removal rate (MRR) with Cu electrode was, approximately, 4.5 times higher than that obtained with a C electrode. In fact, it was found that copper electrode rotating at 20 rpm combined with high values of discharge energy (I = 2 A; ti = 70 µs) is the most economical option in terms of production cost and production time, as it gives a high MRR of 0.4754 mm3/min and a minimum electrode wear (EW) value of 7.52%. Moreover, slightly higher values of MRR were achieved for CuC electrode compared to those obtained with C electrode, indicating that the addition of Cu in the electrode contributes to a greater removal of material. However, a value of Ra of 0.37 µm could be obtained by setting low current intensity values (I = 0.5 A; ti = 45 µs) combined with C electrodes and with no rotation.
Open Access
Analysis of AM parameters on surface roughness obtained in PLA parts printed with FFF technology
(MDPI, 2021) Buj Corral, Irene; Sánchez Casas, Xabier; Luis Pérez, Carmelo Javier; Ingeniería; Ingeniaritza
Fused filament fabrication (FFF) 3D printing technology allows very complex parts to be obtained at a relatively low cost and in reduced manufacturing times. In the present work, the effect of main 3D printing parameters on roughness obtained in curved surfaces is addressed. Polylactic acid (PLA) hemispherical cups were printed with a shape similar to that of the acetabular part of the hip prostheses. Different experiments were performed according to a factorial design of experiments, with nozzle diameter, temperature, layer height, print speed and extrusion multiplier as variables. Different roughness parameters were measured—Ra, Rz, Rku, Rsk—both on the outer surface and on the inner surface of the parts. Arithmetical mean roughness value Ra and greatest height of the roughness profile Rz are usually employed to compare the surface finish among different manufacturing processes. However, they do not provide information about the shape of the roughness profile. For this purpose, in the present work kurtosis Rku and skewness Rsk were used. If the height distribution in a roughness profile follows a normal law, the Rku parameter will take a value of 3. If the profile distribution is symmetrical, the Rsk parameter will take a value of 0. Adaptive neural fuzzy inference system (ANFIS) models were obtained for each response. Such models are often employed to model different manufacturing processes, but their use has not yet been extended to 3D printing processes. All roughness parameters studied depended mainly on layer height, followed by nozzle diameter. In the present work, as a general trend, Rsk was close to but lower than 0, while Rku was slightly lower than 3. This corresponds to slightly higher valleys than peaks, with a rounded height distribution to some degree.