Open Access
Optimization in nanocoated D-shaped optical fiber sensors
(Optical Society of America, 2017) Del Villar, Ignacio; Zubiate Orzanco, Pablo; Ruiz Zamarreño, Carlos; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Gobierno de Navarra / Nafarroako Gobernua
Nanocoated D-shaped optical fibers have been proven as effective sensors. Here, we show that the full width at half minimum (FWHM) of lossy mode resonance can be reduced by optimizing the nanocoating width, thickness and refractive index. As a counterpart, several resonances are observed in the optical spectrum for specific conditions. These resonances are caused by multiple modes guided in the nanocoating. By optimizing the width of the coating and the imaginary part of its refractive index, it is possible to isolate one of these resonances, which allows one to reduce the full width at half minimum of the device and, hence, to increase the figure of merit. Moreover, it is even possible to avoid the need of a polarizer by designing a device where the resonance bands for TE and TM polarization are centered at the same wavelength. This is interesting for the development of optical filters and sensors with a high figure of merit.
Open Access
Wavelength and phase detection based SMS fiber sensors optimized with etching and nanodeposition
(IEEE, 2016) Cardona-Maya, Yamile; Del Villar, Ignacio; Socorro Leránoz, Abián Bentor; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Botero-Cadavid, Juan F.; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua, 2016/PI008; Gobierno de Navarra / Nafarroako Gobernua, 2016/PC025; Gobierno de Navarra / Nafarroako Gobernua, 2016/PC026
The development of an optical fiber refractometer by hydrogen fluoride etching and sputtering deposition of a thin-film of indium tin oxide on a single-mode-multimode-single-mode fiber structure has been analyzed with the aim of improving the sensitivity to the changes of the refractive index (RI) of the external medium. The device is sensitive to the RI changes of the surrounding medium, which can be monitored by tracking the spectral changes of an attenuation band or with a fast Fourier transform (FFT) analysis. By using an optical spectrum analyzer combined with a simple FFT measurement technique, the simultaneous real time monitoring is achieved. The results show that the sensitivity depends on the thin-film thickness. A maximum of 1442 nm/RIU (refractive index unit) in the 1.32–1.35RIUrange has been attained. In addition, a theoretical analysis has been performed, where simu lationsmatched with the experimental results. As a practical appli cation of the developed optical fiber structure, a °Brix (°Bx) sensor has been implemented with a sensitivity of 2.13 nm/°Bx and 0.25 rad/°Bx respectively for wavelength and phase shift detection.
Open Access
Optical fiber refractometers based on sputtered indium tin oxide coatings
(IEEE, 2011) López, S.; Ruiz Zamarreño, Carlos; Hernáez, M.; Del Villar, Ignacio; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
This work presents the fabrication of optical fiber refractometers based on indium tin oxide (ITO) coatings deposited by sputtering with response in the visible spectral region. ITO thin-films have been sputtered by employing a rotating mechanism that enables the fabrication of smooth and homogeneous coatings onto the optical fiber core. Fabricated ITO coated optical fiber devices present several resonances in the visible and near infrared region. These resonances show high optical power attenuations (more than 10 dB) in the visible spectral region, which produces changes in the colour of the output visible light. Therefore, since these resonances shift as a function of the refractive index (RI) of the surrounding medium it is feasible to determine the RI of the outer medium in contact with the ITO coating by simply monitoring the chromatic coordinates (colour change), x and y, of the visible output light
Open Access
SnO2 based optical fiber refractometers
(SPIE, 2012) Sánchez Zábal, Pedro; Ruiz Zamarreño, Carlos; Hernáez Sáenz de Zaitigui, Miguel; Del Villar, Ignacio; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua
In this work, the fabrication and characterization of refractometers based on lossy mode resonances (LMR) is presented. Tin dioxide (SnO2) films deposited on optical fibers are used as the LMR supporting coatings. These resonances shift to the red as a function of the external refractive index, enabling the fabrication of robust and highly reproducible wavelength-based optical fiber refractometers. The obtained SnO2-based refractometer shows an average sensitivity of 7198 nm/refractive index unit (RIU) in the range 1.333-1.420 RIU.
Open Access
Resonances in coated long period fiber gratings and cladding removed multimode optical fibers: a comparative study
(Optical Society of America, 2010) Del Villar, Ignacio; Ruiz Zamarreño, Carlos; Hernáez Sáenz de Zaitigui, Miguel; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
Two optical fiber devices have been coated in parallel: a long period fiber grating (LPFG) and a cladding-removed multimode optical fiber (CRMOF). The progressive coating of the LPFG by means of the layer-by-layer electrostatic-self-assembly, permits to observe a resonance wavelength shift of the attenuation bands in the transmission spectrum. The cause of this wavelength shift is the reorganization of the cladding mode effective indices. The cause of this modal reorganization can be understood with the results observed in the CRMOF coated in parallel. A lossy-moderesonance (LMR) is generated in the same wavelength range of the LPFG attenuation bands analyzed. Moreover, the thickness range where the wavelength shift of the LPFG attenuation bands occurs coincides exactly with the thickness range where the LMR can be visualized in the transmission spectrum. These phenomena are analyzed theoretically and corroborated experimentally. The advantages and disadvantages of both optical fiber devices are explained.
Open Access
Deposition of coatings on long-period fiber gratings: tunnel effect analogy
(Springer, 2006) Del Villar, Ignacio; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua
The sensitivity of Long-period fiber gratings (LPFGs), coated with high-refractive-index thin film overlays, to the refractive index and the thickness of the overlay, and to the ambient refractive index, can be enhanced with a design based on a two-overlay coating of an LPFG. The first overlay of lower refractive index than the cladding affects the guidance of a cladding mode in the second overlay of higher refractive index than the cladding. This causes a more abrupt cladding modal redistribution than with the deposition of a unique high-refractive-index overlay. The phenomenon is analyzed with a method based on a vectorial analysis of modes and the application of coupled mode theory.
Open Access
A comprehensive review of optical fiber refractometers: toward a standard comparative criterion
(Wiley, 2019) Urrutia Azcona, Aitor; Del Villar, Ignacio; Zubiate Orzanco, Pablo; Ruiz Zamarreño, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Thanks to the peculiarities of optical fiber and its ability to be combined with nanotechnology, precise and accurate measurements of the changes in optical properties (i.e., refractive index) of the medium surrounding the fiber are becoming possible with a high degree of performance. Thus, optical fiber sensors (OFSs) are increasingly finding applications in biochemistry and biomedicine. Here, all types of optical fiber refractometers are covered, and they are classified into three main groups: interferometers, grating-based structures, and resonance-based structures (the resonance is induced by coating the optical fiber sensor with a thin film). The performance of these different structures is compared by means of the most common parameters: sensitivity, full width at half minimum or maximum, figure of merit, and quality factor. The aim here is to provide a reliable and easy-to-use tool to compare the performance of the most recent developments on fiber optic refractometers.
Open Access
Fiber-based label-free D-dimer detection for early diagnosis of venous thromboembolism
(SPIE, 2020) Zubiate Orzanco, Pablo; Urrutia Azcona, Aitor; Ruiz Zamarreño, Carlos; Fernández Irigoyen, Joaquín; Giannetti, Ambra; Baldini, Francesco; Díaz Lucas, Silvia; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Santamaría Martínez, Enrique; Del Villar, Ignacio; Chiavaioli, Francesco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
D-dimer is a useful diagnostic biomarker for deep vein thrombosis or pulmonary embolism, collectively referred to as venous thromboembolism (VTE). The ability to detect in real-time the amount of D-dimer with a fast and reliable method is a key step to anticipate the appearance of these diseases. The combination of fiber-optic-based platforms for biosensing with the nanotechnologies is opening up the chance for the development of in situ, portable, lightweight, versatile, reliable and high-performance optical sensing devices towards lab-on-fiber technology. The generation of lossy mode resonances (LMRs) by means of the deposition of nm-thick absorbing metal-oxide films on special geometric-modified fibers allows measuring precisely and accurately surface refractive index changes, which are due to the binding interaction between a biological recognition element and the analyte under investigation. This approach enhances the light-matter interaction in a strong way, thus turning out to be more sensitive compared to other optical technology platforms, such as fiber gratings or surface plasmon resonance. Here, the results of a highly specific and sensitive biosensor for the detection of D-dimer based on LMR in fiber-optics are presented by monitoring in real-time the shift of the LMR related to the biomolecule interactions thanks to a conventional wavelength-interrogation system and an ad-hoc developed microfluidics. A detection limit of 100 ng/mL, a value 5-fold below the clinical cutoff value, has been attained for D-dimer spiked in human serum. The comparison of the results achieved with proteomics-based methodologies, which allows for the identification of betaand gamma-chains of fibrinogen, demonstrates the ability of our platform to specifically (>90%) recognize D-dimer.
Open Access
Strategies for fabrication of hydrogen peroxide sensors based on electrostatic self-assembly (ESA) method
(Elsevier, 2004) Del Villar, Ignacio; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Echeverría Morrás, Jesús; Claus, Richard O.; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua
An optical fiber sensor has been fabricated for detection of 5 M–0.1mM concentrations of hydrogen peroxide with a linear response. The deposition method used is electrostatic self-assembly (ESA) of polymer cationic and anionic layers. Prussian Blue (PB) has been included in the polycation layers. The optical fiber sensor is included in a reflection setup, where the measuring technique is based on the slope of the optical reflected power change caused by oxidation of Prussian White (PW) to Prussian Blue. The sensor recovers after immersion in a reductive agent and is immune against a variety of components. Measurement of hydrogen peroxide has been proved successfully in a wide range pHs between 3 and 9. Some techniques have been applied in order to avoid the lost of indicator.
Open Access
Lossy mode resonance sensors based on lateral light incidence in nanocoated planar waveguides
(Nature Research, 2019) Fuentes Lorenzo, Omar; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua, 2018/PC021-022
The deposition of an indium oxide (In2O3) thin film on conventional planar waveguides (a coverslip and a glass slide) allows generating lossy mode resonances (LMR) by lateral incidence of light on the waveguide and by registering the optical spectrum in a spectrometer. This novel sensing system becomes an alternative to optical fibre, the substrate where LMR-based sensors have been developed so far, since it is easier to handle and more robust. An additional advantage is that cost effective waveguides, such as slides or coverslips, can be used in a platform that resembles surface plasmon resonance-based sensors in the Kretschmann configuration but without the need for a coupling prism and with the advantage of being able to generate TE and TM LMR resonances with metallic oxide or polymer thin films. The results are corroborated with simulations, which provide in-depth understanding of the phenomena involved in the sensing system. As a proof-of-concept for the optical platform, two refractometers were developed, one with low sensitivity and for a wide range of refractive indices, and the other with higher sensitivity but for a narrower refractive index range. The sensors presented here open up the path for the development of LMR-based chemical sensors, environmental sensors, biosensors, or even the generation of other optical phenomena with the deposition of multilayer structures, gratings or nanostructures, which is much easier in a planar waveguide than in an optical fibre.