Open Access
Highly sensitive sensor for measuring material thermal expansion using a ring laser
(IEEE, 2023) Díaz Lucas, Silvia; Fuentes Lorenzo, Omar; Torres Betancourt, Angie Tatiana; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A new thermal expansion sensor is presented in this letter. It combines an interferometric fiber sensor and an erbium-doped fiber ring laser as the light source. The sensor consists of a combination of single-mode, hollow-core, and no-core mirror fibers. The sensor was tested on two different types of based metal, such as aluminum and steel, giving sensitivities as high as 38.7 and 5.75 nm/°C, respectively, showing good performance.
Open Access
High sensitivity lossy-mode resonance refractometer using low refractive index PFA planar waveguide
(Elsevier, 2023) Domínguez Rodríguez, Ismel; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ascorbe Muruzabal, Joaquín; Del Villar, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work a new strategy to improve the sensitivity of refractometers based on lossy-mode resonances has been proved. The proximity of the PFA (tetrafluoroethylene-perfluoro polymer) substrate refractive index to that of water has permitted to implement an optical refractometer with a sensitivity of 41,034 nm per refractive index unit (nm/RIU) for refractive indices ranging from 1.3318 to 1.3347. The work is supported with both theoretical and experimental results. This high sensitivity can be used for the development of LMR based chemical sensors and biosensors, where a low limit of detection is required, with the additional advantage of a simple disposable planar configuration.
Embargo
Experimental study of sensing performance using hyperbolic mode resonances
(Elsevier, 2025-01-01) Matías Maestro, Ignacio; Del Villar, Ignacio; Corres Sanz, Jesús María; González Salgueiro, Lázaro José; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Surface plasmon resonance (SPR) and lossy mode resonance (LMR) are prominent sensing mechanisms utilized across various fields. The Kretschmann configuration is commonly employed for SPR, while LMR is favored in planar waveguides or optical fibers due to high incidence angles. Recently, hyperbolic mode resonance (HMR) has emerged as a hybrid approach, combining metallic and dielectric thin films. This study explores the impact of incidence angle on HMR using the Kretschmann configuration. Four samples with varying gold (Au) and tin dioxide (SnO2) layer thicknesses were fabricated and characterized using Atomic Force Microscopy (AFM). Experimental setups employed the Kretschmann configuration for reflectance spectrum analysis. Results indicate enhanced sensitivity and figure of merit (FoM) with an additional SnO2 layer compared to the case without SnO2. Particularly with a 36 nm Au thickness the sensitivity doubles and the FoM improves by 16 %. Numerical simulations validate these findings, confirming the optimized performance of HMR for specific layer thicknesses and incidence angles.
Open Access
Lossy mode resonance-based sensors in planar configuration: a review
(IEEE, 2023) Matías Maestro, Ignacio; Del Villar, Ignacio; Corres Sanz, Jesús María; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Lossy mode resonance (LMR)-based sensors have attracted much interest during the last decade in the domain of optical fiber (OF). Here, it is shown that the progress made in the transfer of this technology to planar waveguides (PWs) with different sensing applications such as environmental sensors and biosensors. In addition, the inherent advantages in terms of robustness, simplicity, and easiness to generate novel complex structures are discussed.
Open Access
Extraordinary sensitivity with quasi-lossy mode resonance mode transition bands in long period fiber gratings
(Elsevier, 2025-01-16) González Salgueiro, Lázaro José; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This study presents a novel sensor design utilizing a long-period fiber grating (LPFG) deposited with a TiO2 nanocoating via atomic layer deposition. The study combines theoretical simulations and experimental validation to optimize the grating period and modulation index to operate in the mode transition with a quasi-lossy mode resonance (LMR) behavior, i.e., the LPFG attenuation bands shift similarly to LMRs. This enables the achievement of a remarkable sensitivity of 78 nm/nm, allowing for the detection of sub-angstrom variations in film thickness, which is critical for applications in semiconductor manufacturing. Our setup facilitates continuous monitoring of the transmission spectrum, enabling real-time adjustments during deposition to maximize sensitivity. As proof of concept for the applicability of the sensor as a refractive index sensor, we demonstrated exceptional sensitivity for nitrogen detection, achieving around 10,000 nm/RIU, with a figure of merit of 200. This marks one the highest sensitivities reported for optical fiber gas sensors and suggests this technology could revolutionize the field duet to its simplicity in terms of sensor design.
Open Access
Spectral measurements with hybrid LMR and SAW platform for dual parameter sensing
(Royal Society of Chemistry, 2022) Domínguez Rodríguez, Ismel; Del Villar, Ignacio; Corres Sanz, Jesús María; Lachaud, Jean-Luc; Yang, Yang; Hallil, Hamida; Dejous, Corinne; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Lossy mode resonance (LMR)-based optical sensors change their wavelength upon contact with substances or gases. This allows developing applications to detect the refractive index of the surrounding medium and even the thickness of the biolayers deposited on the waveguide. In the same way, when acoustic sensors are in contact with a liquid, it is possible to determine parameters, especially mechanical ones such as shape of the particle or molecule, mass load, elastic constants and viscosity of the liquid. This work reports the development of a system that combines LMR with surface acoustic wave (SAW) technologies to characterize a liquid in terms of its refractive index and viscosity simultaneously. Conveniently prepared glucose solutions are used for sensor calibration. The refractive index of the solutions ranges from 1.33 to 1.41 and its viscosity ranges from 1.005 mPa·s to 9 mPa·s, respectively. A sensitivity of 332 nm per RIU has been achieved with the optical sensor while the acoustic sensor has shown a sensitivity of −1.5 dB/(mPa·s). This new combinational concept could be expanded to the development of more demanding applications such as chemical sensors or biosensors.
Open Access
A study on the EDM drilling of reaction-bonded silicon carbide using different electrode materials
(Springer, 2023) Torres Salcedo, Alexia; Luis Pérez, Carmelo Javier; Puertas Arbizu, Ignacio; Corres Sanz, Jesús María; Ingeniería; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Today, there is a growing demand for efficient hole manufacturing technology in many industries such as aeronautics, automotive and nuclear, among others. Thus, the present study deals with the machining of through holes on SiSiC advanced ceramic by using Electrical Discharge Machining (EDM) drilling technology. Since recommendations related to the electrode characteristics and settings parameters are found to be scant for the industrial use of EDM drilling of SiSiC ceramics, this research work comes to cover this gap as it presents a complete study focused on the influence on different electrodes under rough and finish machining conditions. In particular, the influence of four electrodes materials (copper, copper-tungsten, graphite and copper infiltrated graphite) and three different electrode diameters ranging from 2 to 4 mm are investigated. In addition, the rotational speed of the electrode is also analysed. From the experimental results, both electrode material and machining regime, seem to be the most relevant factors of all. In the case of 2 mm diameter electrode, material removal rate (MRR) with Cu electrode was, approximately, 4.5 times higher than that obtained with a C electrode. In fact, it was found that copper electrode rotating at 20 rpm combined with high values of discharge energy (I = 2 A; ti = 70 µs) is the most economical option in terms of production cost and production time, as it gives a high MRR of 0.4754 mm3/min and a minimum electrode wear (EW) value of 7.52%. Moreover, slightly higher values of MRR were achieved for CuC electrode compared to those obtained with C electrode, indicating that the addition of Cu in the electrode contributes to a greater removal of material. However, a value of Ra of 0.37 µm could be obtained by setting low current intensity values (I = 0.5 A; ti = 45 µs) combined with C electrodes and with no rotation.
Open Access
Planar-waveguide-lmr-based sensors: engineering the depth of characteristic curves
(IEEE, 2023) Shrivastav, Anand M.; Del Villar, Ignacio; Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Lossy mode resonance (LMR)-based sensors have been proven as one of the exponentially growing research fields since the last decade. These sensors have demonstrated their capabilities in the detection of several physical, chemical, and biological entities, such as refractive index, humidity, gases, enzymes, etc. Conventionally, LMR-based sensors are developed using optical fiber as the sensing platform, but to increase the broad range of applications and better tenability, planar waveguide substrates for LMR realization have been introduced in the last few years. This provides a greater degree of freedom for the sensor design such as tunability in substrate thickness, material, and better surface immobilization. The current study focuses on evaluating the effect of substrate thickness on LMR-based optical sensors to achieve higher sensing performance. For experiments, 150-μm-thick glass coverslips are used as the thin planer substrate, which is then coated with a few nanometers thick LMR-supported SnO 2 layer using the dc sputtering method. Furthermore, to monitor the effect of the changing substrate thickness, the width of the glass coverslip is reduced through the chemical etching process using the 40% HF solution, and simultaneously, the changes in LMR spectra are analyzed. The study shows that the depth of LMR curves strongly depend on the thickness of the waveguide providing LMRs with lower substrate thickness possesses higher depth. Greater depth in LMR curves is a crucial factor in identifying the minimum transmission wavelength of resonance, making it easier to track and detect the targeted parameter. This characteristic greatly enhances the applicability of LMR-based sensors in industrial applications.
Open Access
Multichannel refractometer based on lossy mode resonances
(IEEE, 2022) Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Domínguez Rodríguez, Ismel; Del Villar, Ignacio; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this work a new multiparameter sensor platform based on lossy mode resonances is presented. The structure consists of a soda-lime optical slab waveguide butt-coupled to multimode optical fibers. A variable thickness thin-film is deposited to generate multiple independent resonances on the same waveguide, which can be monitored using a single spectrometer. In order to show the potentiality of the structure, a broad resonance was selectively narrowed by etching sections of the LMR producer thin film. The spectral width is progressively reduced, allowing to selectively isolate independent resonances, which opens the path for multiple LMR generation in the same spectra in a multiparameter sensing platform. The experimental results were corroborated with a theoretical analysis based on the finite difference method (FDM). As a proof of concept, two refractometers on the same waveguide were fabricated and tested using PDMS cells. This platform can be easily miniaturized in order to integrate multiple sensors at low cost, what can be of interest for the development of multi-analyte biosensors probes. IEEE
Open Access
Electrochemical lossy mode resonance for the detection of manganese ions
(Elsevier, 2023) Domínguez Rodríguez, Ismel; Corres Sanz, Jesús María; Del Villar, Ignacio; Mozo, Juan D.; Simerova, Radka; Sezemsky, Petr; Stranak, Vitezslav; Smietana, Mateusz; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work we propose electrochemical lossy mode resonance (eLMR) as a powerful method for the detection of manganese (Mn) ions. The sensor is based on a simple planar waveguide (sodasingle bondlime glass coverslip) coated with a thin layer of indium tin oxide (ITO) to obtain an optical resonance effect. Simultaneously, the ITO layer served as the working electrode in the cathodic stripping voltammetry (CSV) of Mn. The eLMR sensor is capable of simultaneously performing electrochemical (EC) and optical measurements, specifically lossy mode resonance (LMR), to monitor the growth of the adsorbed Mn layer on the ITO electrode and the electrochemically modulated diffusion layer. For Mn2+ ions, a limit of detection (LoD) of 1.26 ppb has been demonstrated using the EC method, whereas the optical method exhibited a LoD of 67.76 ppb. The results obtained indicate significant potential for application in molecular electrochemistry and studies focused on electrified interfaces.