Person:
Teniente Vallinas, Jorge

person.page.identifierURI

https://academica-e.unavarra.es/handle/2454/50076

Last Name

Teniente Vallinas

First Name

Jorge

person.page.departamento

Ingeniería Eléctrica, Electrónica y de Comunicación

person.page.instituteName

ISC. Institute of Smart Cities

ORCID

0000-0001-9643-5479

person.page.upna

2694

Full item page

Search Results

Now showing 1 - 10 of 10

Open Access
New coplanar waveguide based on the gap waveguide technology
(IEEE, 2021) Biurrun Quel, Carlos; Teniente Vallinas, Jorge; Río Bocio, Carlos del; Institute of Smart Cities - ISC
A new planar waveguide, coined Inverted coplanar gap waveguide is presented. The concept of gap waveguides and parallel plate suppression between perfect magnetic and a perfect electric conductors is applied to coplanar waveguides in order to create a low-dispersion, low-loss transmission line. The combination of an artificial magnetic conductor and channelized top cover allow the propagation of an even coplanar mode with a strong component propagating over the air while solving encapsulation matters without the use of metallic vias. The main theory behind this new concept is presented and supported by FEM simulations on a commercial software package.
Open Access
Silicon integrated subharmonic mixer on a photonic-crystal platform
(IEEE, 2021) Torres García, Alicia E.; Pérez Escudero, José Manuel; Teniente Vallinas, Jorge; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This paper presents a planar silicon integrated subharmonic mixer on top of a photonic-crystal platform. The local oscillator (LO) power is injected through a 2D photoniccrystal (PC) slab to a resonant cavity that effectively couples the signal to a planar bow-tie antenna. The same antenna, which is printed on the top of the PC cavity, contains an antiparallel Schottky diode pair which performs the down-conversion. The proposed design is a simple, easy to integrate, low cost, low profile device. Moreover, the described fabrication process is compatible with active components integration. The performance of the design has been experimentally demonstrated showing good agreement with the simulation and is comparable with the stateof-the-art of planar mixers. The work presented here is based on concepts and technologies from electronics and photonics domains and may be a good starting point for the creation of new devices, allowing the integration and upgrading of existing techniques from both worlds.
Open Access
Design and characterization of terahertz CORPS beam forming networks
(Springer, 2023) Biurrun Quel, Carlos; Haddad, Thomas; Sievert, Benedikt; Kress, Robin; Weimann, Nils; Erni, Daniel; Rennings, Andreas; Stöhr, Andreas; Teniente Vallinas, Jorge; Río Bocio, Carlos del; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This work reviews the design and applicability of beam-forming networks based on Coherently Radiating Periodic Structures (CORPS-BFN) at Terahertz (THz) frequency bands. These versatile networks offer two operation modes: a continuous beam steering – feeding an antenna array with a linearly progressive phase distribution – using a reduced number of phase controls; or a multi-beam operation, generating independent, overlapped beams. These networks are built upon the concatenation of power combiners/dividers (PCDs) with isolated outputs. The isolation is provided by monolithically integrated resistors, implemented with Ti/TiO thin films for the first time. In this work, a planar prototype of a (inputs/outputs) microstrip CORPS-BFN for operation in the WR3.4/WM-864 band (220–330 GHz) on a thin 50 m Indium Phosphide (InP) substrate is designed, fabricated, and characterized. The measured S-parameters show a reflection coefficient better than -15 dB and an insertion loss between 1.6 and 3.2 dB in the whole band. In addition, an isolation better than 20 dB between the input ports has been measured. An overall remarkable agreement is observed between the measurements and the simulations. Last, the applications, scalability and efficiency of this type of networks at the targeted band are discussed in detail.
Open Access
Fully metallic Luneburg metalens antenna in gap waveguide technology at V-band
(IEEE, 2023) Pérez Quintana, Dayan; Bilitos, Christos; Ruiz-García, Jorge; Ederra Urzainqui, Íñigo; Teniente Vallinas, Jorge; González-Ovejero, David; Beruete Díaz, Miguel; Institute of Smart Cities - ISC
This article presents the design of a flat Luneburg metalens antenna at V-band using gap waveguide (GW) technology. The metalens consists of a parallel plate waveguide (PPW) loaded with metallic pins whose height is modulated to get an effective refractive index that follows the Luneburg equation. A Groove GW (GGW) H-plane horn is used to illuminate the metalens, such that the rays are collimated and a planar wavefront is generated in the direction of propagation. Since the structure at hand is planar, it can be efficiently integrated on flat surfaces. Moreover, the fully metallic structure is mechanically robust and presents lower losses than lenses including dielectric substrates. A prototype has been fabricated and tested, simulations and experimental results are in very good agreement. The metalens yields an input reflection coefficient (S11) below −10 dB from 45 to 70 GHz, whereas the −3 dB gain fractional bandwidth is 26.2% with respect to a center frequency of 60 GHz, with a peak of 22.5 dB at 61 GHz. These features make this design an interesting solution for millimeter-wave (MMW) applications.
Open Access
Photonic-assisted 2-D terahertz beam steering enabled by a LWA array monolithically integrated with a BFN
(Optica, 2022) Haddad, Thomas; Biurrun Quel, Carlos; Lu, Peng; Tebart, Jonas; Sievert, Benedikt; Makhlouf, Sumer; Grzeslo, Marcel; Teniente Vallinas, Jorge; Río Bocio, Carlos del; Stöhr, Andreas; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A novel photonic-assisted 2-D Terahertz beam steering chip using only two tuning elements is presented. The chip is based on an array of three leaky wave antennas (LWAs) with a monolithically integrated beamforming network (BFN) on a 50 µm-thick indium phosphide substrate. The THz beam angle in elevation (E-plane) is controlled via optical frequency tuning using a tunable dual-wavelength laser. An optical delay line is used for azimuth (H-plane) beam control. The simulated beam scanning range is 92° in elevation for a frequency sweep from 0.23 THz to 0.33 THz and 69.18° in azimuth for a time delay of 3.6 ps. For the frequency range from 0.26 THz to 0.32 THz, it is confirmed experimentally that the THz beam scans from −12° to +33°, which is in good agreement with the numerical simulations. The beam direction in azimuth scans with a total angle of 39° when applying a delay difference of 1.68 ps. A good agreement is found between theoretically predicted and experimentally determined THz beam angles with a maximum angle deviation below 5°. The experimental scanning angles are limited due to the mechanical constraints of the on-wafer probes, the on-chip integrated transition and the bandwidth of the THz receiver LNA. The mechanical limitation will be overcome when using a packaged chip.
Open Access
The Canfranc Axion Detection Experiment (CADEx): search for axions at 90 GHz with Kinetic Inductance Detectors
(IOP Publishing, 2022) Aja, Beatriz; Arguedas Cuendis, Sergio; Arregui Padilla, Iván; Artal, Eduardo; Barreiro, R. Belén; Casas, Francisco J.; Ory, Marina C. de; Díaz-Morcillo, Alejandro; Fuente, Luisa de la; Gallego, Juan Daniel; García-Barceló, José María; Gimeno, Benito; Gómez, Alicia; Granados, Daniel; Kavanagh, Bradley J.; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Lozano-Guerrero, Antonio José; Magaz, María T.; Martín-Pintado, Jesús; Martínez-González, Enrique; Miralda-Escudé, Jordi; Monzó-Cabrera, Juan; Najarro de la Parra, Francisco; Navarro-Madrid, José R.; Nuñez Chico, Ana B.; Pascual, Juan Pablo; Pelegrin, Jorge; Peña Garay, Carlos; Rodríguez, David; Socuéllamos, Juan M.; Teberio Berdún, Fernando; Teniente Vallinas, Jorge; Vielva, Patricio; Vila, Iván; Vilar, Rocío; Villa, Enrique; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
We propose a novel experiment, the Canfranc Axion Detection Experiment (CADEx), to probe dark matter axions with masses in the range 330–460 μeV, within the W-band (80–110 GHz), an unexplored parameter space in the well-motivated dark matter window of Quantum ChromoDynamics (QCD) axions. The experimental design consists of a microwave resonant cavity haloscope in a high static magnetic field coupled to a highly sensitive detecting system based on Kinetic Inductance Detectors via optimized quasi-optics (horns and mirrors). The experiment is in preparation and will be installed in the dilution refrigerator of the Canfranc Underground Laboratory. Sensitivity forecasts for axion detection with CADEx, together with the potential of the experiment to search for dark photons, are presented.
Open Access
Reduced loss and prevention of substrate modes with a novel coplanar waveguide based on gap waveguide technology
(MDPI, 2023) Biurrun Quel, Carlos; Teniente Vallinas, Jorge; Río Bocio, Carlos del; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
The Gap Waveguide technology utilizes an Artificial Magnetic Conductor (AMC) to prevent the propagation of electromagnetic (EM) waves under certain conditions, resulting in various gap waveguide configurations. In this study, a novel combination of Gap Waveguide technology and the traditional coplanar waveguide (CPW) transmission line is introduced, analyzed, and demonstrated experimentally for the first time. This new line is referred to as GapCPW. Closed-form expressions for its characteristic impedance and effective permittivity are derived using traditional conformal mapping techniques. Eigenmode simulations using finite-element analysis are then performed to assess its low dispersion and loss characteristics. The proposed line demonstrates an effective suppression of the substrate modes in fractional bandwidths up to 90%. In addition, simulations show that a reduction of up to 20% of the dielectric loss can be achieved with respect to the traditional CPW. These features depend on the dimensions of the line. The paper concludes with the fabrication of a prototype and validation of the simulation results in the W band (75–110 GHz).
Open Access
Ultrathin and high-efficiency Pancharatnam-Berry phase metalens for millimeter waves
(AIP Publishing, 2021) Moreno-Peñarrubia, Alexia; Teniente Vallinas, Jorge; Kuznetsov, Sergei A.; Orazbayev, Bakhtiyar; Beruete Díaz, Miguel; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Applying the Pancharatnam–Berry (PB) principle to half-wave plate (HWP) metasurfaces allows the manipulation of wavefronts along with the conversion of the handedness of circularly polarized incident waves by simply rotating the meta-atoms that compose the metasurface. PB metasurfaces (PBM) working in transmission mode with four or more layers have been demonstrated to reach levels of transmission effi- ciency near 100% but also have resulted in bulky structures. On the other hand, compact tri-layer ultrathin (k/8) designs have reached levels near 90% but are more challenging than single- or bi-layer structures from a manufacturing viewpoint. Here, we propose a compact ultrathin (
Open Access
A novel ku-band circularly-polarized horn antenna based on a ridged wall
(IEEE, 2023) Marzo Oyarbide, Andoni; Teberio Berdún, Fernando; Teniente Vallinas, Jorge; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, a novel wideband (31.5 % bandwidth) circularly-polarized antenna based on a ridged wall is presented. A pair of ridges on the inner wall of the horn serves as an inbuilt polarizer, which can generate left-hand or right-hand circular polarization without any additional polarizer. The ridged wall is placed at 45° with respect to the input port linearly polarized wave to generate a 90° phase delay and obtain the desired circular polarization at the aperture. The simulated results show that the antenna works great in the whole Ku satellite band (from 10.7 to 14.7 GHz) with more than 20 dB return loss and below 1 dB axial ratio. The antenna can be fabricated using traditional computer numerical control machining techniques or the new 3D metal additive manufacturing processes.
Open Access
High-yield waveguide diplexer for low-cost E-band 5G point-to-point radio links
(IEEE, 2022) Teberio Berdún, Fernando; Calero Fernández, Ibai; Arregui Padilla, Iván; Martín Iglesias, Petronilo; Teniente Vallinas, Jorge; Gómez Laso, Miguel Ángel; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This paper presents the design and realization of a high-yield tuning-less waveguide diplexer and a high-gain lens horn antenna for 5G point-to-point fixed-beam communications at the frequency ranges of 71/76 GHz and 81/86 GHz (E-band). The diplexer is composed of two bandpass filters based on the combination of a low-pass filtering function and a high-pass structure. The diplexer provides very relaxed fabrication tolerances. A prototype has been fabricated and measured showing return loss better than 20 dB and attenuation levels higher than 60 dB. The insertion loss is better than 1 dB. A lens horn antenna which provides more than 38 dBi gain is utilized to provide high directivity at the same frequencies. The proposed sub-system combines the advantages of high-performance and simple mechanical assembly finding, it especially attractive for 5G applications due to the reduced fabrication cost.