Open Access
Nanocoated optical fibre for lossy mode resonance (LMR) sensors and filters
(IEEE, 2015) Del Villar, Ignacio; Arregui San Martín, Francisco Javier; Corres Sanz, Jesús María; Bariáin Aisa, Cándido; Goicoechea Fernández, Javier; Ruiz Zamarreño, Carlos; Elosúa Aguado, César; Hernáez Sáenz de Zaitigui, Miguel; Rivero Fuente, Pedro J.; Socorro Leránoz, Abián Bentor; Urrutia Azcona, Aitor; Sánchez Zábal, Pedro; Zubiate Orzanco, Pablo; López Torres, Diego; Acha Morrás, Nerea de; Ascorbe Muruzabal, Joaquín; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
Nanometer scale coatings with a complex refractive index deposited on optical fibre permit to obtain attenuation bands in the transmission spectrum, whose central wavelength coincides with the moment when a mode guided in the optical fibre cladding starts to be guided in the coating. Due to the complex refractive index of the coating, the guided mode is a lossy mode. Consequently, these attenuation bands receive the name of lossy mode resonances. This phenomenon can be used for development of ultra-high sensitivity photonic devices (for detection, among others, of volatile organic compounds, pH and refractive index) or for optical filtering. In this work, rules for adequate design are indicated based on numerical results obtained with FIMMWAVE and on experimental results that corroborate the theoretical predictions.
Open Access
Optical fiber vacuum sensor based on modal interferometer and PDMS coating
(IEEE, 2019) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This work studies the behavior of polydimethylsiloxane (PDMS) as a transducer for optical vacuum pressure measurements. The optical structure chosen for this device is a modal interferometer achieved by splicing a coreless multimode optical fiber between two single mode fibers. Then, an etching process is applied to the obtained device, in order to decrease the diameter of the fiber and increase the sensitivity. Finally, the fiber is coated by dip-coating with a layer of PDMS, which changes its volume with pressure changes. The device has been studied in the 1x10(-3) mbar to 10 mbar range with a wavelength shift of 4 nm. A maximum sensitivity of 35 nm/mbar was obtained. The simple fabrication process, which can be applied to more sensitive structures, suggest that PDMS can be a good choice for the development of optical fiber vacuum sensors.
Open Access
Optical fiber vacuum sensor based on etched SMS structure and PDMS coating
(IEEE, 2020) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Corres Sanz, Jesús María; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, an optical fiber vacuum sensor based on a single-mode multimode single-mode (SMS) structure coated with polydimethylsiloxane (PDMS) is studied. The SMS structure generates an interferometric pattern based on multimode interference. The structure is dip-coated with a layer of PDMS, whose optical properties change when it is subjected to varying vacuum pressure. Different strategies are applied in an attempt to improve the final performance of the sensor, such as decreasing the diameter of the fiber and modifying the properties of the coating by modifying the proportion of solvent. Decreasing the diameter of the optical fiber and using toluene as a solvent are both proved to be successful strategies for increasing the sensitivity of the sensor. The devices are studied in the 1×10-3–10 mbar range with a maximum wavelength shift of 12 nm, leading to a maximum sensitivity of 35 nm/mbar. The simplicity of the fabrication process, which can be applied to more sensitive structures, suggests that PDMS may be a good choice for the development of optical fiber vacuum sensors.
Open Access
Highly sensitive sensor for measuring material thermal expansion using a ring laser
(IEEE, 2023) Díaz Lucas, Silvia; Fuentes Lorenzo, Omar; Torres Betancourt, Angie Tatiana; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A new thermal expansion sensor is presented in this letter. It combines an interferometric fiber sensor and an erbium-doped fiber ring laser as the light source. The sensor consists of a combination of single-mode, hollow-core, and no-core mirror fibers. The sensor was tested on two different types of based metal, such as aluminum and steel, giving sensitivities as high as 38.7 and 5.75 nm/°C, respectively, showing good performance.
Open Access
Electrochemical lossy mode resonance for the detection of manganese ions
(Elsevier, 2023) Domínguez Rodríguez, Ismel; Corres Sanz, Jesús María; Del Villar, Ignacio; Mozo, Juan D.; Simerova, Radka; Sezemsky, Petr; Stranak, Vitezslav; Smietana, Mateusz; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work we propose electrochemical lossy mode resonance (eLMR) as a powerful method for the detection of manganese (Mn) ions. The sensor is based on a simple planar waveguide (sodasingle bondlime glass coverslip) coated with a thin layer of indium tin oxide (ITO) to obtain an optical resonance effect. Simultaneously, the ITO layer served as the working electrode in the cathodic stripping voltammetry (CSV) of Mn. The eLMR sensor is capable of simultaneously performing electrochemical (EC) and optical measurements, specifically lossy mode resonance (LMR), to monitor the growth of the adsorbed Mn layer on the ITO electrode and the electrochemically modulated diffusion layer. For Mn2+ ions, a limit of detection (LoD) of 1.26 ppb has been demonstrated using the EC method, whereas the optical method exhibited a LoD of 67.76 ppb. The results obtained indicate significant potential for application in molecular electrochemistry and studies focused on electrified interfaces.
Open Access
Improving the width of lossy mode resonances in a reflection configuration D-shaped fiber by nanocoating laser ablation
(Optical Society of America, 2020) Fuentes Lorenzo, Omar; Vaiano, Patrizio; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua
The full width at half maximum (FWHM) of lossy mode resonances (LMRs) in the optical spectrum depends on the homogeneity of the thin film deposited. In this Letter, a method for improving the FWHM is applied for an LMR generated by a D-shaped optical fiber in reflection configuration. For this purpose, three samples with different attenuation were deposited with DC sputtering thin films of SnO2−x, and a further controlled immersion of the samples in water was performed. A laser-cleaner method was used to improve the FWHM characteristics of one of the samples from 106 to 53 nm. This improvement can be applied to thin-film-based sensors where there is a problem with the inhomogeneity of the coating thickness. Moreover, with this technique, it was proved that a coated length of just 3–4 mm permits the generation of an LMR, with implications for the miniaturization of the final device.
Open Access
Spectral evolution with incremental nanocoating of long period fiber gratings
(Optical Society of America, 2006) Del Villar, Ignacio; Corres Sanz, Jesús María; Achaerandio Alvira, Miguel; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
The incremental deposition of a thin overlay on the cladding of a long-period fiber grating (LPFG) induces important resonance wavelength shifts in the transmission spectrum. The phenomenon is proved theoretically with a vectorial method based on hybrid modes and coupled mode theory, and experimentally with electrostatic self-assembly monolayer process. The phenomenon is repeated periodically for specific overlay thickness values with the particularity that the shape of the resonance wavelength shift depends on the thickness of the overlay. The main applications are the design of wide optical filters and multiparameter sensing devices.
Open Access
Fiber-optic biosensor based on lossy mode resonances
(Elsevier, 2012) Socorro Leránoz, Abián Bentor; Corres Sanz, Jesús María; Del Villar, Ignacio; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Open Access
Generation of lossy mode resonances in planar waveguides toward development of humidity sensors
(IEEE, 2019) Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Del Villar, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Lossy mode resonances (LMRs) are typically obtained with optical fibre. The Kretschmann configuration is an alternative but LMRs are generated with angles approaching grazing incidence. In this work, a new setup is explored, based on the lateral incidence of light on conventional planar waveguides such as glass slides or coverslips. Indium tin oxide was deposited onto both types of waveguides generating LMRs. The results of the simulations carried out agree well with the experimental results. As an example of the potential of this new and simple optical configuration, a humidity sensor with a sensitivity of 0.212 nm/% relative humidity (RH) in the range from 65% to 90% of RH was developed, which expedites the development of other types of sensors already explored with LMR-based optical fibre sensors.
Open Access
Planar-waveguide-lmr-based sensors: engineering the depth of characteristic curves
(IEEE, 2023) Shrivastav, Anand M.; Del Villar, Ignacio; Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Lossy mode resonance (LMR)-based sensors have been proven as one of the exponentially growing research fields since the last decade. These sensors have demonstrated their capabilities in the detection of several physical, chemical, and biological entities, such as refractive index, humidity, gases, enzymes, etc. Conventionally, LMR-based sensors are developed using optical fiber as the sensing platform, but to increase the broad range of applications and better tenability, planar waveguide substrates for LMR realization have been introduced in the last few years. This provides a greater degree of freedom for the sensor design such as tunability in substrate thickness, material, and better surface immobilization. The current study focuses on evaluating the effect of substrate thickness on LMR-based optical sensors to achieve higher sensing performance. For experiments, 150-μm-thick glass coverslips are used as the thin planer substrate, which is then coated with a few nanometers thick LMR-supported SnO 2 layer using the dc sputtering method. Furthermore, to monitor the effect of the changing substrate thickness, the width of the glass coverslip is reduced through the chemical etching process using the 40% HF solution, and simultaneously, the changes in LMR spectra are analyzed. The study shows that the depth of LMR curves strongly depend on the thickness of the waveguide providing LMRs with lower substrate thickness possesses higher depth. Greater depth in LMR curves is a crucial factor in identifying the minimum transmission wavelength of resonance, making it easier to track and detect the targeted parameter. This characteristic greatly enhances the applicability of LMR-based sensors in industrial applications.