Open Access
Study of effect of nickel content on tribocorrosion behaviour of nickel-aluminium-bronzes (NABs)
(MDPI, 2023) Berlanga Labari, Carlos; Claver Alba, Adrián; Biezma Moraleda, María Victoria; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
The simultaneous existence of mechanical erosion and electrochemical corrosion is a common scenario for engineering alloys used in marine environments, such as pump impellers and valves. Nickel–aluminium–bronzes (NABs) are widely used alloys in these environments due to their combination of high corrosion resistance and effective mechanical properties. However, NAB alloys are increasingly cast with reduced nickel content due to its high price and low availability. In this study, we examined the tribocorrosion behaviour of two nickel–aluminium bronzes (C95500 and C95400) with different nickel contents (4.8% and 1.0%, respectively) by means of a pin-on-disk device combined with in situ electrochemistry under 1 M NaCl solution. We conducted tests for pure wear in distilled water, pure corrosion using in situ electrochemistry under 1 M NaCl solution, and a combination of wear and corrosion, called tribocorrosion, to understand the overall synergism that exists between the two. We analysed our results using gravimetric as well as volumetric analysis; in addition, we defined the friction coefficient to compare the effect of open-circuit potential (OCP). We also applied the Tafel method and compared corrosion rates for the different scenarios. We employed confocal microscopy to delimitate the impact of the surface topography of pure wear and its synergistic effect with corrosion, and used an optical microscope to study the materials’ microstructures as cast conditions. We also utilised XRD in the Bragg–Brentano configuration to determine the chemical composition of corrosion products. From the experiments conducted, we concluded that an important synergistic effect existed between the wear and corrosion of both NABs, which was associated with corrosion-induced wear. We found NAB C95400 to be more susceptible to erosion under both conditions compared with NAB C95500 due to the chemical composition and lubricant effect of corrosion products formed during the tribocorrosion tests, which were supported by the enriched Ni corrosion products, particularly the presence of nickel-rich copper chloride, 3Cu3(CuNi)(OH)6CuCl2, in the C95500 alloy. We concluded that, because it increased the nickel content, the NAB alloy offered better wear and corrosion behaviour in sea water conditions due to its protective film nature.
Open Access
Mapping the research landscape of bauxite by-products (red mud): an evolutionary perspective from 1995 to 2022
(Elsevier, 2024) Svobodova-Sedlackova, Adela; Calderón, Alejandro; Fernández, A. Inés; Chimenos, Josep Maria; Berlanga Labari, Carlos; Yücel, Onuralp; Barreneche, Camila; Rodríguez Trías, Rafael; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
The global population growth has significantly impacted energy and raw material consumption, unmatched since the Industrial Revolution. Among metals, aluminium ranks second only to steel, with annual production exceeding 69 million tonnes. Due to its high demand, bauxite, the primary ore from which aluminium is extracted, is now classified as a critical material in the EU and the US, given the potential risk of supply shortages for essential applications. Geographical and production challenges surround bauxite, presenting geo-economic and environmental challenges. A critical concern in aluminium production is managing by-products, notably red mud, a bauxite residue, generating over 175 million tonnes annually worldwide. Comprehensive bibliometric research is imperative due to the high amount of bibliographical resources related to this topic, encompassing circular economy, re-valorisation, sustainability, and disposal. This study employs bibliometric methods to assess red mud valorisation, offering insights into research topics, influential authors, and key journals, shedding light on the past, present, and future of red mud research. Such bibliometric analysis not only highlights the current state of the field but also serves as a valuable tool for decision-making, enabling researchers and policymakers to identify trends, gaps, and areas for further exploration, fostering informed and sustainable advancements in the by-products of the aluminium industry.
Open Access
Valorisation of red mud: disclosing the potential of an abundant residue
(MDPI, 2025-02-21) Vielma, Carlos A.; Svobodova-Sedlackova, Adela; Chimenos, Josep Maria; Fernández, A. Inés; Berlanga Labari, Carlos; Rodríguez Trías, Rafael; Barreneche, Camila; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Gobierno de Navarra / Nafarroako Gobernua
Red mud (RM), the primary waste product of the aluminium industry, is notable for its high concentrations of metals and rare earth elements (REE). Efforts have been made to develop extraction methods for REE recovery from RM, aiming to enhance its valorisation and reduce the European reliance on external REE sources—particularly crucial for technological advancements and the transition to renewable energy. However, these methods have only been limited to low technology readiness levels (TRLs), with no economically or technically viable processing routes yet defined to enable large-scale industrialisation within a circular economy model. This study characterised RM samples from the Seydişehir region in Türkiye using different techniques and explored the experimental process for recovering metals and REE. Moreover, the study assessed the global prospective potential of RM based on technical and economic data, as well as the sustainability of the implemented process through the life cycle assessment (LCA) tool. Results showed a total REE concentration of up to 1600 ppm, with Ce, being the most abundant (426 ± 27 ppm), followed by La, Nd, and Sc. Concentration efficiencies for La and Nd ranged between 240–300%. Sc, Y, Ce, La, and Nd have significant usage in European markets and represent prime RM targets for further prospecting. The LCA revealed that the highest global warming potential of the sequential extraction process was attributed to hydroxylamine hydrochloride and hydrogen peroxide. The findings highlight the need to explore alternative, more eco-friendly reagents to improve RM valorisation.
Open Access
A comprehensive study on hot corrosion resistance of NiCoCrAlYTa and NiCrAl thermal-sprayed coatings for CSP applications
(Elsevier, 2023) Aristu Ojer, Daniel; Berlanga Labari, Carlos; Alberro, Mikel; Rández Diago, Xabier; Fernández, Ángel G.; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
The new generation of concentrated solar power (CSP) plants could be able to work at temperatures up 650 °C and carbonates molten salts are one of the main candidates to be used as thermal energy storage (TES) materials. Molten salt corrosion has been defined as one of the main issues and the technology demands more resistance alloys and innovative coatings. In this study, the assessment of hot corrosion resistance for NiCoCrAlYTa and NiCrAl thermal-sprayed coatings has been undertaken, tested on a ternary eutectic mixture (Li2CO3-Na2CO3-K2CO3) at a temperature of 650 °C. Electrochemical impedance spectroscopy and linear polarization resistance tests were used to evaluate the behaviour of the coatings but the obtained results reveal high values of corrosion rates accompanied by the formation of cracks. This unsatisfactory performance of the coatings, analysed by scanning electron microscopy and x-ray diffraction, can be attributed to a combination of different factors such as porosity, internal material stresses and thermal diffusion phenomena. As a result, it is concluded that further research is necessary to explore new coating application techniques.
Open Access
A comprehensive review of fatigue strength in pure copper metals (DHP, OF, ETP)
(MDPI, 2024) Jiménez Ruiz, Eduardo; Lostado Lorza, Rubén; Berlanga Labari, Carlos; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
Due to their exceptional electrical and thermal conductivity properties, high-purity copper (Cu-DHP) and copper alloys of similar composition, such as electrolytic tough-pitch (ETP), oxygen-free electronic (OFE) and oxygen-free (OF), have often been used in the manufacture of essential components for the electrical, electronic and power generation industries. Since these components are subject to cyclic loads in service, they can suffer progressive structural damage that causes failure due to fatigue. The purpose of this review is to examine the most relevant aspects of mechanical fatigue in Cu-DHP, ETP, OFE and OF. The impact of many factors on fatigue strength (Se), including the frequency, temperature, chemical environment, grain size, metallurgical condition and load type, were analyzed and discussed. Stress–life (S-N) curves under zero mean stress (σm = 0) were found for high-cycle fatigue (HCF). For non-zero mean stress (σm ≠ 0), stress curves were based on a combination of Gerber, Soderberg and ASME elliptic failure criteria. Stress–life (S-N) curves were also developed to correlate fatigue strength (Se) with stress amplitude (σa), yield strength (Syp) and ultimate strength (Sut). Finally, for low-cycle fatigue (LCF), strain–life (ε-N) curves that establish a relationship between the number of cycles to failure (N) and total strain amplitude (εplastic) were determined. Hence, this review, as well as the proposed curves, provide valuable information to understand fatigue failure for these types of materials.