ISC - Institute of Smart Cities

Permanent URI for this community

http://hdl.handle.net/2454/20316

Browse

Now showing 1 - 20 of 20

Open Access
Along-the-path exponential integration for Floquet stability analysis of wind turbines
(IOP Publishing, 2022) Ros Ganuza, Javier; Olcoz Alonso, Álvaro; Plaza Puértolas, Aitor; Zientziak; Institute of Smart Cities - ISC; Ciencias; Gobierno de Navarra / Nafarroako Gobernua
Traditionally, stability assessment of wind turbines has been performed by eigenanalysis of the azimuthally-averaged linearized system after applying the Multi-Blade Coordinate (MBC) transformation. However, due to internal or external anisotropy, the MBC transform does not produce an exact Linear Time-Invariant (LTI) system, and a Floquet analysis is required to capture the influence of all periodic terms, leading to a more accurate stability analysis. In this paper exponential integration methods that use system linearizations at different blade azimuth positions are used to integrate the perturbed system state and compute the Floquet monodromy matrix. The proposed procedure is assessed for a simple 6 DOF wind turbine model and a more complex aeroelastic model of a 5MW onshore wind turbine. The defined along-the-path or moving-point exponential integrator is found to be the suitable in order to perform a Floquet stability analysis even using a coarse linearization grid.
Open Access
Analog lock-in amplifier design using subsampling for accuracy enhancement in GMI sensor applications
(MDPI, 2023) Algueta-Miguel, Jose M.; Beato López, Juan Jesús; López Martín, Antonio; Ciencias; Zientziak; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, PJUPNA2005
A frequency downscaling technique for enhancing the accuracy of analog lock-in amplifier (LIA) architectures in giant magneto-impedance (GMI) sensor applications is presented in this paper. As a proof of concept, the proposed method is applied to two different LIA topologies using, respectively, analog and switching-based multiplication for phase-sensitive detection. Specifically, the operation frequency of both the input and the reference signals of the phase-sensitive detector (PSD) block of the LIA is reduced through a subsampling process using sample-and-hold (SH) circuits. A frequency downscaling from 200 kHz, which is the optimal operating frequency of the employed GMI sensor, to 1 kHz has been performed. In this way, the proposed technique exploits the inherent advantages of analog signal multiplication at low frequencies, while the principle of operation of the PSD remains unaltered. The circuits were assembled using discrete components, and the frequency downscaling proposal was experimentally validated by comparing the measurement accuracy with the equivalent conventional circuits. The experimental results revealed that the error in the signal magnitude measurements was reduced by a factor of 8 in the case of the analog multipliers and by a factor of 21 when a PSD based on switched multipliers was used. The error in-phase detection using a two-phase LIA was also reduced by more than 25%.
Open Access
A combination of a vibrational electromagnetic energy harvester and a giant magnetoimpedance (GMI) sensor
(MDPI, 2020) Beato López, Juan Jesús; Royo Silvestre, Isaac; Algueta-Miguel, Jose M.; Gómez Polo, Cristina; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua
An energy harvesting device combined with a giant magnetoimpedance (GMI) sensor is presented to analyze low frequency vibrating systems. An electromagnetic harvester based on magnetic levitation is proposed for the electric power generation. The device is composed of two fixed permanent magnets at both ends of a cylindrical frame, a levitating magnet acting as inertial mass and a pick-up coil to collect the induced electromotive force. At the resonance frequency (10 Hz) a maximum electrical power of 1.4 mW at 0.5 g is generated. Moreover, an amorphous wire was employed as sensor nucleus for the design of a linear accelerometer prototype. The sensor is based on the GMI effect where the impedance changes occur as a consequence of the variations of the effective magnetic field due to an oscillating magnetic element. As a result of the magnet’s periodic motion, an amplitude modulated signal (AM) was obtained, its amplitude being proportional to mechanical vibration amplitude (or acceleration). The sensor’s response was examined for a simple ferrite magnet under vibration and compared with that obtained for the vibrational energy harvester. As a result of the small amplitudes of vibration, a linear sensor response was obtained that could be employed in the design of low cost and simple accelerometers.
Open Access
Complex selective manipulations of thermomagnetic programmable matter
(Springer Nature, 2022) Irisarri Erviti, Josu; Ezcurdia Aguirre, Íñigo Fermín; Sandúa Fernández, Xabier; Galarreta Rodríguez, Itziar; Pérez de Landazábal Berganzo, José Ignacio; Marzo Pérez, Asier; Ciencias; Zientziak; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
Programmable matter can change its shape, stiffness or other physical properties upon command. Previous work has shown contactless optically controlled matter or magnetic actuation, but the former is limited in strength and the latter in spatial resolution. Here, we show an unprecedented level of control combining light patterns and magnetic fields. A mixture of thermoplastic and ferromagnetic powder is heated up at specific locations that become malleable and are attracted by magnetic fields. These heated areas solidify on cool down, and the process can be repeated. We show complex control of 3D slabs, 2D sheets, and 1D filaments with applications in tactile displays and object manipulation. Due to the low transition temperature and the possibility of using microwave heating, the compound can be manipulated in air, water, or inside biological tissue having the potential to revolutionize biomedical devices, robotics or display technologies.
Open Access
Contactless magnetic nanoparticle detection platform based on non-linear GMI effect
(Elsevier, 2021) Beato López, Juan Jesús; Algueta-Miguel, Jose M.; Gómez Polo, Cristina; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación
A detection platform based on non-linear Giant Magnetoimpedance Effect was analyzed for the design of a contactless and low-cost detector of magnetic nanoparticles. The sensor consists of two soft magnetic amorphous wires (Co66Fe2Si13B15Cr4, 1.5 cm in length) placed in parallel and connected electrically in series. Initially, a simple voltage divider was employed to characterize the variations of the first, V1fand second harmonic, V2f, voltages. Their response was analyzed under the effect of the remnant magnetic field generated by different amounts of Fe3O4 nanoparticles (mean diameter 140 nm) as a function of an external magnetic field, H. Due to the larger relative variations showed by V2f, the second harmonic was chosen for the final prototype development. An electronic interface was designed for both current excitation and V2f detection. The designed detection platform, characterized by high detection sensitivity, low-cost, portable, and reusable features, can be employed to efficiently detect magnetic nanoparticles.
Open Access
Determination of hazardous vapors from the thermal decomposition of organochlorinated silica xerogels with adsorptive properties
(Elsevier, 2024) Rosales Reina, María Beatriz; Cruz Quesada, Guillermo; Pujol, Pablo; Reinoso, Santiago; Elosúa Aguado, César; Arzamendi Manterola, Gurutze; López Ramón, María Victoria; Garrido Segovia, Julián José; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
The incorporation of organic groups into sol-gel silica materials is known to have a noticeable impact on the properties and structure of the resulting xerogels due to the combination of the properties inherent to the organic fragments (functionality and flexibility) with the mechanical and structural stability of the inorganic matrix. However, the reduction of the inorganic content in the materials could be detrimental to their thermal stability properties, limiting the range of their potential applications. Therefore, this work aims to evaluate the thermal stability of hybrid inorganic-organic silica xerogels prepared from mixtures of tetraethoxysilane and organochlorinated triethoxysilane precursors. To this end, a series of four materials with a molar percentage of organochlorinated precursor fixed at 10%, but differing in the type of organic group (chloroalkyls varying in the alkyl-chain length and chlorophenyl), has been selected as model case study. The gases and vapors released during the thermal decomposition of the samples under N2 atmosphere have been analyzed and their components determined and quantified using a thermogravimetric analyzer coupled to a Fourier-transform infrared spectrophotometer and to a gas chromatography-mass spectrometry unit. These analyses have allowed to identify up to three different thermal events for the pyrolysis of the organochlorinated xerogel materials and to elucidate the reaction pathways associated with such processes. These mechanisms have been found to be strongly dependent on the specific nature of the organic group.
Open Access
Development of a cognitive IoT-enabled Smart Campus
(IEEE, 2024-08-23) Picallo Guembe, Imanol; Klaina, Hicham; López Iturri, Peio; Azpilicueta Fernández de las Heras, Leyre; Celaya Echarri, Mikel; Astrain Escola, José Javier; Villadangos Alonso, Jesús; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Estadística, Informática y Matemáticas; Estatistika, Informatika eta Matematika; Ciencias; Zientziak; Institute of Smart Cities - ISC
The evolution from Smart to Cognitive Cities takes advantage, among others, of advanced communication technologies in order to increase interactivity levels. In this work, an analysis of wireless connectivity within the framework of a Smart Campus pilot at the Public University of Navarra in Spain is presented. By means of in-house implemented hybrid deterministic code, multiple wireless connectivity conditions with different operating frequencies are presented. The use of these tools provides accurate coverage/capacity analysis of large, complex scenarios, aiding in the design of network devices as well as overall network topology in order to optimize overall performance.
Open Access
Diffuse irradiance on tilted planes in urban environments: evaluation of models modified with sky and circumsolar view factors
(Elsevier, 2021) García Ruiz, Ignacio; Blas Corral, María Ángeles de; Hernández Salueña, Begoña; Sáenz Gamasa, Carlos; Torres Escribano, José Luis; Ingeniaritza; Zientziak; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería; Ciencias
Numerous studies have analyzed existing irradiance models for estimating sky diffuse irradiance on tilted planes. However, few have evaluated the suitability of these models for estimating irradiance in obstructed environments, specifically considering the effects of obstacles. In this study, three irradiance models —one of them with five variants— for estimating diffuse irradiance on tilted planes located in urban environments were evaluated. All models have been adapted to consider the effect of an urban canyon on the diffuse irradiance received on a tilted plane through the sky view factor and the circumsolar view factor. All the models were evaluated against the diffuse irradiance values obtained by the ISO 15469:2004(E)/CIE S 011/E:2003 angular distribution model. Therefore, it was necessary to determine the standard sky type corresponding to each record of the measurements performed by a sky scanner at the radiometric station of UPNA (Spain). A total of 4,864 scenarios were considered to occur from the combination of different orientations and inclinations of the plane, and different orientations and aspect ratios of the urban canyon. The results revealed that the Perez model considering a 35° half-angle circumsolar region has the best performance, followed by the Perez model considering a 45° half-angle circumsolar region.
Open Access
Electromagnetic vibrational harvester based on U-shaped ferromagnetic cantilever: a novel two-magnet configuration
(Elsevier, 2024-09-07) Gandía Aguado, David; Garayo Urabayen, Eneko; Beato López, Juan Jesús; Royo Silvestre, Isaac; Cruz Blas, Carlos Aristóteles de la; Tainta Ausejo, Santiago; Gómez Polo, Cristina; Ciencias; Zientziak; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Estadística, Informática y Matemáticas; Estatistika, Informatika eta Matematika; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
Electromagnetic vibrational harvesters are low-cost devices featuring high-power densities and robust structures, often used for capturing the energy of environmental vibrations (civil infrastructures, transportation, human motion, etc.,). Based on Faraday's law, energy generation relies on the modification of the magnetic field distribution within a magnetic element caused by mechanical vibrations inducing an electromotive force (EMF) in a pick-up coil. However, the practical implementation of this type of vibrational harvester is currently limited due to the reduced generated power under low-frequency vibrations. In this work, an electromagnetic vibrational harvester is experimentally characterized and analyzed employing magnetic circuit analysis. The harvester consists of a ferromagnetic U-shaped cantilever, a NdFeB magnet and a ferrite magnet used as ¿magnetic tip mass¿ to enhance the magnetic flux changes under vibrations of frequency < 100 Hz. For this configuration, an experimental voltage of ¿ 1.2 V peak-to-peak (open circuit) was obtained at a resonant frequency of 77 Hz, enabling the subsequent electronic rectification stage. Additionally, Finite Element Method (FEM) is used to explore different design possibilities including the modeling of complex geometries, mechanical properties and non-linear magnetic materials, enabling the tuning of the resonance frequency from 51 to 77 Hz, keeping constant the induced voltage.
Open Access
Enabling anything to anything connectivity within urban environments towards cognitive frameworks
(IEEE, 2024-08-23) Picallo Guembe, Imanol; Klaina, Hicham; López Iturri, Peio; Azpilicueta Fernández de las Heras, Leyre; Celaya Echarri, Mikel; Astrain Escola, José Javier; Villadangos Alonso, Jesús; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Estadística, Informática y Matemáticas; Estatistika, Informatika eta Matematika; Ciencias; Zientziak; Institute of Smart Cities - ISC
The evolution from Smart Cities towards Cognitive Cities is enabled, among others, by the use of flexible and adaptive communication systems, capable of providing high levels of interactivity among multiple systems and users. In this work, wireless connectivity in full volumetric scale is analyzed, in order to provide wireless links between any device/user within the scenario, spanning to different applications from vehicular connectivity at different levels or infrastructure related communications, among others.
Open Access
From fundamental materials chemistry to sensing applications: unravelling the water adsorption mechanism of a luminescent optical fibre sensor membrane
(Elsevier, 2024) Cruz Quesada, Guillermo; Rosales Reina, María Beatriz; López Torres, Diego; Reinoso, Santiago; López Ramón, María Victoria; Arzamendi Manterola, Gurutze; Elosúa Aguado, César; Espinal Viguri, Maialen; Garrido Segovia, Julián José; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This work provides insight into the correlation between the luminescent response of a water-vapour optical fibre sensor and the textural properties of its lanthanide-doped silica coating. To this end, a library of 16 silica xerogels derived from combinations between 2 lanthanide dopants (EuIII, TbIII) and 8 antenna ligands was synthesised and characterised by photoluminescence spectroscopy and N2 and CO2 adsorption-desorption isotherms, among others. Based on the best luminescent response and most-suited porous texture, the material doped with TbIII and 2,2′-(4-(2-Ethoxyethoxy)pyridine-2,6-diyl)bis(4,5-dihydrooxazole) was selected to construct the probe. A film of this material was affixed to a commercial silica fibre by dip-coating and the resulting sensor was tested in a climatic chamber with relative humidity ranging from 20 to 90% to obtain normalised time-response and calibration curves at three temperatures. The response was linear up to certain water-vapour concentrations, beyond which abruptly changed to polynomial, acting against the sensor resolution. The adsorption mechanism was elucidated by comparing the isosteric enthalpies of adsorption calculated from the sensor calibration curves to those determined from the monolith water-vapour isotherms, revealing that capillary condensation in the membrane mesopores was the key phenomenon leading to the response deviating from linearity.
Open Access
A lock-in amplifier for magnetic nanoparticle detection using GMI sensors
(IEEE, 2024-09-30) Algueta-Miguel, Jose M.; Beato López, Juan Jesús; López Martín, Antonio; Gómez Polo, Cristina; Ciencias; Zientziak; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
A digital lock-in amplifier (LIA) for contactless magnetic nanoparticle (MNP) detection using giant magnetoimpedance (GMI) sensors is presented. The proposed approach is based on the simultaneous detection of the second harmonic amplitude and phase. A Xilinx Artix-7 field-programmable gate array (FPGA) has been employed for efficiently implementing the phase-sensitive detection (PSD) and the subsequent digital processing. The analog GMI sensor interface has been designed for minimizing the dependence of the excitation current on the GMI sensor impedance, also enhancing the rejection of the parasitic second-order distortion produced by the setup. A subsampling process of the analog outputs has been applied, both increasing the effective resolution of the analog-to-digital converter (ADC) and facilitating signal recovery. The proposed system improves the MNP detection capability reported in previous works using the second harmonic amplitude. Moreover, a characterization of the phase response, which had not been previously studied in the literature, is also provided.
Open Access
Luminance calibration of a full sky HDR imaging system using sky scanner measurements
(Solar Energy Society, 2022) García Ruiz, Ignacio; Sáenz Gamasa, Carlos; Hernández Salueña, Begoña; García Santos, Rafael; Torres Escribano, José Luis; Zientziak; Ingeniaritza; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Ingeniería
A full sky High Dynamic Range imaging system, based on a Single-Lens Reflex camera with a fisheye lens, has been constructed and calibrated with a sky scanner luminance meter. The method considers the geometrical, spectral, timing and orientation issues between instruments. The calibration data sets, having nearly simultaneous measurements under stable sky conditions, were obtained from approximately one month of data using selection variables based in the experimental design. For luminance estimation we use the standard 𝐶𝐼𝐸𝑌 RGB combination and a Spectrally Matched Luminance (𝑆𝑀𝐿) predictor, matching the spectral response of the instruments. With 738 calibration points having luminances up to 23.6 kcd∕m2, covering 98.5% of the sky luminance range, 𝐶𝐼𝐸𝑌 is linearly correlated with sky scanner measurements with a coefficient of determination 𝑅2 = 0.9927 and a Root Mean Squared Error (𝑅𝑀𝑆𝐸) of 7.7%. 𝑆𝑀𝐿 gives better results, with 𝑅2 = 0.9973 and 𝑅𝑀𝑆𝐸 = 5.3%. With 253 calibration points with luminances up to 12.9 kcd∕m2, comprising 94.1% of the sky luminance range, both predictors clearly improve, with 𝑅2 = 0.9964 and 𝑅𝑀𝑆𝐸 = 4.1% in case of 𝐶𝐼𝐸𝑌 and 𝑅2 = 0.9982 and 𝑅𝑀𝑆𝐸 = 2.9% in case of 𝑆𝑀𝐿.
Open Access
Magnetic binary encoding system based on 3D printing and GMI detection prototype
(Elsevier, 2022) Beato López, Juan Jesús; Algueta-Miguel, Jose M.; Galarreta Rodríguez, Itziar; López Ortega, Alberto; Garayo Urabayen, Eneko; Gómez Polo, Cristina; Aresti Bartolomé, Maite; Soria Picón, Eneko; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Zientziak; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Gobierno de Navarra / Nafarroako Gobernua; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work, the feasibility of a magnetic binary encoding system using 3D printing technology is analyzed. The study has a double interest, that is, the possibility of printing a 3D piece that contains the codified information and the development of a system for its decoding. For this purpose, magnetic nanoparticles (magnetite Fe3O4) were embedded in a polymeric matrix of Polylactic Acid (PLA) and Poly-ε-caprolactone (PCL). Similar to a conventional barcode, a rectangular piece with an alternating pattern of strips with absence (only polymer) and a 5 wt% of embedded magnetic nanoparticles was 3D printed employing the Fused Deposition Modelling tech- nique (FDM). The information was decoded by means of a Giant Magnetoimpedance (GMI) sensor-based pro- totype, by scanning the surface of the piece and measuring the changes in the magnetic field. As sensor nucleus, an amorphous soft magnetic wire of nominal composition (Co0.94 Fe0.06)72.5 Si12.5 B15 was employed. The decoding prototype incorporates a homemade electronic sensor interface that permits, at the time, the GMI sensor excitation and the subsequent signal conditioning to optimize its response. The output signal enables the detection of the magnetite nanoparticles and the magnetic decoding of the encoded information (“1” and “0”, presence or absence of the magnetic nanoparticles, respectively).
Open Access
Monitoring structural transformations in metamagnetic shape memory alloys by non-contact GMI technology
(IOP Publishing, 2023) Beato López, Juan Jesús; La Roca, Paulo Matías; Algueta-Miguel, Jose M.; Garayo Urabayen, Eneko; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Different applications based on metamagnetic shape memory alloy (MSMA) require monitoring the evolution of the martensitic transformation (MT) to optimize the actuation mechanism. To avoid interaction with the active material, a non-contact technique would be ideal. Nevertheless, non-contact detection involves complex methods like diffraction, optical analysis, or electromagnetic technology. The present work demonstrates that the MT can be monitored without interaction with the active material using a low-cost technology based on the Giant Magnetoimpedance (GMI) effect. The GMI sensor is based on a (CoFe)SiB soft magnetic wire submitted to an alternating current and whose second harmonic voltage variation allows to detect changes in the strength of the stray magnetic fields linked to the metamagnetic phase transition. The sensor has been tested using the MT of a NiMnInCo MSMA. A specific application for environmental temperature control using the non-contact GMI sensor is proposed.
Open Access
Non-linear GMI decoding in 3D printed magnetic encoded systems
(Elsevier, 2023) Beato López, Juan Jesús; Algueta-Miguel, Jose M.; Galarreta Rodríguez, Itziar; Garayo Urabayen, Eneko; López Ortega, Alberto; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The nonlinear giant magnetoimpedance (GMI) effect was explored as a highly sensitive sensing technology in 3D-printed magnetic encoded systems. Magnetic nanoparticles with low (magnetite, Fe3O4) and high (Co ferrite, Co0.7Fe2.3O4) magnetic remanence were embedded (10 wt%) in a polymeric matrix of Polylactic Acid (PLA) and Poly-ε-caprolactone (PCL) and extruded in magnetic filaments to be 3D printed by the Fused Deposition Modelling technique (FDM). Two different geometries were constructed namely, individual magnetic strips and fixed barcoded pieces. The stray magnetic fields generated by the magnetic nanoparticles were detected through the non-linear (second harmonic) GMI voltage using a soft magnetic CoFeSiB wire as the nucleus sensor. The decoding response was analyzed as a function of the magnetization remanence of the nanoparticles, the distance between the individual magnetic strips, and the position (height) of the GMI decoding sensor. It has been shown that modification of the net magnetization direction of each individual fixed strip within the barcode geometry is possible through the application of local external magnetic fields. This possibility improves the versatility of the 3D binary encoding system by adding an additional state (0 without nanoparticles, 1 or −1 depending on the relative orientation of the net magnetization along the strips) during the codifying procedure.
Open Access
Shear based gap control in 2D photonic quasicrystals of dielectric cylinders
(Optica, 2021) Andueza Unanua, Ángel María; Sevilla Moróder, Joaquín; Pérez Conde, Jesús; Wang, Kang; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Zientziak; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Eléctrica, Electrónica y de Comunicación; Ciencias
2D dielectric photonic quasicrystals can be designed to show isotropic band gaps. In this work we study a quasiperiodic lattice made of silicon dielectric cylinders (ε = 12) arranged as periodic unit cell based on a decagonal approximant of a quasiperiodic Penrose lattice. We analyze the bulk properties of the resulting lattice as well as the bright states excited in the gap, which correspond to localized resonances of the electromagnetic field in specific cylinder clusters of the lattice. Then we introduce a controlled shear deformation γ which breaks the decagonal symmetry and evaluate the width reduction of the gap together with the evolution of the resonances, for all shear values compatible with physical constraints (cylinder contact). The gap width reduction reaches 18.5% while different states change their frequency in several ways. Realistic analysis of the actual transmission of the electromagnetic radiation, often missing in the literature, has been performed for a finite 'slice' of the proposed quasicrystals structure. Two calculation procedures based on MIT Photonic Bands (MPB) and Finite Integration Technique (FIT) are used for the bulk and the finite structures showing an excellent agreement between them.
Open Access
Smarterial – Smart matter optomagnetic
(2021) Irisarri Erviti, Josu; Marzo Pérez, Asier; Galarreta Rodríguez, Itziar; Estatistika, Informatika eta Matematika; Ingeniaritza; Zientziak; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Estadística, Informática y Matemáticas; Ingeniería; Ciencias
Smart materials, also known as programmable materials, are a combination of different components that have the capability to change shape, move around and adapt to numerous situations by applying an external controllable field. Previous works have used optically guided matter or magnetically actuated materials, but similarly to soft robots, they are limited in spatial resolution or strength. Here we propose combining a low temperature thermoplastic polymer Polycaprolactone (PCL) with ferromagnetic powder particles (Fe). Focused light can heat this compound at specific locations and make it malleable. These heated spots can be actuated by external magnetic fields. Once the material cools down, this process can be repeated, or reversed. The compound can be actuated contact-less in the form of 3D slabs, 2D sheets, and 1D filaments. We show applications for reversible tactile displays and manipulation of objects. The laboratory team has characterised the density, weight, magnetic attraction, magnetic force, phase change, thermal and electrical conductivity and heat difusión (spread point test) for smart ferromagnetic compounds of different mixture proportions. The main advantages of this smart matter optomagnetic are the high spatial resolution of light and the strong force of magnetic attraction whilst mechanical properties of polymers are practically conserved. Due to the low temperature required and the possibility to use infrared or electromagnetic induction to heat the compound, the smart material can be used in air, water, or inside biological tissue. Eventually, Smart materials will enrich collaborative movements, such as grab and hold, and more complex ones, as reshaping and reassembling.
Open Access
Strain sensing based on resonant states in 2D dielectric photonic quasicrystals
(Optica, 2021) Andueza Unanua, Ángel María; Pérez Conde, Jesús; Sevilla Moróder, Joaquín; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación
This paper reports the numerical and experimental study of the strain sensing effect of bidimensional quasiperiodic structures made with dielectric cylinders. Structures of around 100 cylinders arranged following a Penrose quasiperiodic disposition were simulated, built and measured, in different states of deformation. The selected quasiperiodic structure contains a symmetric decagonal ring resonator that shows two states in its photonic band gap. The frequency of these states varies linearly in opposite directions as the structure is axially deformed, becoming an interesting sensing principle that can be exploited to build optical strain gauges. As a proof of concept, centimeter-scale glass cylinder (εr=4.5) structures were fabricated and their transmission spectra were measured in the microwave range. The same structures were simulated using finite integration time domain showing a good agreement with the measurements. The sensitivity of the prototype built was 12.4 kHz/µε, very linear in a wide range. Therefore, we conclude that the states in the gap of the resonator rings of 2D quasicrystals can find an interesting application in optical strain gauge construction.
Open Access
Tuning the sensitivity of photonic sensors toward alkanes through the textural properties of hybrid xerogel coatings
(Wiley, 2025-01-15) Rosales Reina, María Beatriz; López Torres, Diego; Cruz Quesada, Guillermo; Espinal Viguri, Maialen; Elosúa Aguado, César; Reinoso, Santiago; Garrido Segovia, Julián José; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This work exemplifies how incorporating organosilane modifiers into silica matrices allows for tuning the optical response of reflection photonic sensors through customizing the textural properties of hybrid xerogel sensing films. Xerogels with propyl molar percentages 0, 5, and 10% are used to construct photonic probes (OFS0pTEOS, OFS5pTEOS and OFS10pTEOS, respectively) by dip-coating upon optimizing film deposition parameters. The time response of these probes toward a battery of volatile organic compounds (VOCs) comprising species with different functionality, size-shape, and polarity is systematically analyzed through ON/OFF experiments, revealing that a low propyl content makes the poor-responding OFS0pTEOS film highly sensitive toward non-aromatic, large molecules with low-polar or non-polar character in OFS5pTEOS. This sensor is particularly sensitive toward alkanes, with globular cyclohexane (cyHex) outperforming elongated n-hexane. Variable-temperature calibration curves obtained from step-by-step experiments and adsorption-desorption cycles corroborate these observations and allow hysteresis to be quantified. The response to cyHex closely follows VOC concentration changes with the most stable signal among analytes, leading to well-defined curves with low-to-negligible hysteresis. The isosteric enthalpies of cyHex adsorption are obtained for both the bulk material and the sensor, demonstrating labile adsorbate-adsorbent interactions ruling the sensor response and becoming more exothermic for larger VOC concentrations.