Listar por autor "López Taberna, Jesús"
Mostrando ítems 21-40 de 49
-
Diseño del busbar de un convertidor de 5 niveles
El objetivo de este proyecto es estudiar las inductancias parásitas de los busbar de distintas topologías de convertidores. En concreto, se quiere cuantificar la inductancia de los busbar de convertidores multinivel. Un ... -
Economic and environmental analysis of PV electricity storage in Sweden
Renewable energies, and among them solar photovoltaics, are becoming more important in the last years due to the lack of fossil fuels and the environmental impact of them. PV installed capacity is increasing over and over ... -
Electric heated windows
The project aim is to investigate the thermal comfort and the energy use aspects of electric heated windows. New technologies are being developed by some companies around the world. These companies develop homogeneous ... -
Energy assessment of waste water heat exchanger and solar energy panel connected to district heating
This project has the aim of calculating the efficiency of the tap water system, in explicit the heating of tap water, in Furugården, Valbo. Furugården is a new retirement home, building Furugården finished in 2013. The ... -
Estudio de diferentes topologías de generación eólica
Este proyecto fin de carrera se enmarca dentro del campo de la electrónica de potencia, aplicada en este caso a la generación eléctrica a partir de energías renovables, más concretamente al sector eólico. Será objeto ... -
Estudio de la propagación de huecos de tensión en parques eólicos
Debido a la creciente importancia de la generación de energía eólica hay ciertos problemas que es conveniente resolver para que la eficiencia de esta generación de energía sea la mejor posible. Uno de esos problemas es la ... -
Estudio teórico y modelización por elementos finitos de una máquina de imanes permanentes
En este proyecto fin de carrera se pretende realizar una breve introducción a la modelización por elementos finitos de las máquinas eléctricas rotativas por medio del programa de simulación JMAG. Para ello, se ha realizado ... -
Estudio y fabricación de un aerogenerador de imanes permanentes
Este proyecto tiene como objeto la construcción de un pequeño aerogenerador para el suministro eléctrico de una pequeña vivienda aislada de la red eléctrica, para satisfacer pequeñas demandas de energía. Para llevar a cabo ... -
Finite element method studies on the stability behavior of cylindrical shells under axial and radial uniform and non-uniform loads
The aim of this project is to analyze the buckling strength of thin cylindrical shells subjected to uniform and non-uniform axial and radial compressive loads. -
Finite element method studies on the stability behavior of external radial loaded cylindrical shells with varying dimensions
With the help of FEM and ANSYS, the influence of varying dimensions and sections, was tested on the structural behavior of cylindrical shells under external radial load. First, the theoretical concepts concerning ... -
Hot deformation of a microalloyed steel
The aim of the project is the study of the deformation behaviour of microalloyed steel by means of processing maps and microstructural characterization. Furthermore a comparison of different types of processing maps is ... -
Influence of the driver and the parameters of damping in the torque at the propeller shaft after a gear shift
In this document, a description of the behaviour of the torque which affects the drive shafts of the vehicle, and consequently the wheels, is explained. For this purpose, it is used the 3D method developed in the Institute ... -
An inverse finite element approach to characterize the mechanical properties of hydrogels
The aim of this thesis is to achieve and to obtain a rheological characterization of hydrogels by means of the finite element method, the parameters which define the biofilm model that has been implemented in ABAQUS ... -
Inversor trifásico de IGBTS
Echarte Azcárate, Xabier (2006) Proyecto Fin de Carrera / Ikasketen Amaierako Proiektua -
Investigation of stress analysis in gear simulations using different model order reduction techniques
The main objective of this work is to simulate the contact between gears and determine if the stress values on the flank of the gear computed with the elastic multibody approach are similar to those obtained with the ... -
Investigation of transformer behavior under DC influence with simulation models and laboratory measurements
The behavior of transformers under DC components has been since long studied. One of the principal sources of these components is the AC-DC energy conversion, in which unsymmetrical direct current components can arise. ... -
Modeling and control of floating wind turbines
Due to the fast development of wind energy and exponential growing of installed wind turbines, the number of places with optimal wind conditions is limited and wind turbines are installed in the sea. For deep sea levels ... -
Modeling of a droop-controlled grid-connected DFIG wind turbine
Oraá Iribarren, Iker; Samanes Pascual, Javier ; López Taberna, Jesús; Gubía Villabona, Eugenio (IEEE, 2022) Artículo / ArtikuluaTraditionally, to characterize the response of droop-controlled systems RMS models have been used. However, as it is demonstrated in this work, when droop control is applied to doubly-fed induction generators, RMS models ... -
Monitorización del consumo eléctrico de un hobar: sensado y acondicionamiento de la corriente
Los contadores inteligentes permiten al usuario conocer en cualquier instante el consumo de electricidad del hogar, mediante la representación de los datos medidos en diferentes gráficas. En este proyecto, realizado por ... -
Monitorización del consumo eléctrico de un hogar: Procesado de datos mediante Arduino
En el mercado actual se están desarrollando diferentes tipos de contadores de consumo eléctrico inteligentes, los cuales permiten al usuario conocer en cualquier ins-tante el consumo de electricidad del hogar mediante la ...